CAP1128 datasheet(33/75 Pages) MICROCHIP

33 / 75 page

 2015 Microchip Technology Inc.

DS00001622B-page 33

CAP1128

6.2.2

SENSOR INPUT STATUS - 03H

The Sensor Input Status Register stores status bits that indicate a touch has been detected. A value of ‘0’ in any bit

indicates that no touch has been detected. A value of ‘1’ in any bit indicates that a touch has been detected.

All bits are cleared when the INT bit is cleared and if a touch on the respective capacitive touch sensor input is no longer

present. If a touch is still detected, the bits will not be cleared (but this will not cause the interrupt to be asserted - see

Section 6.6).

Bit 7 - CS8 - Indicates that a touch was detected on Sensor Input 8.

Bit 6 - CS7 - Indicates that a touch was detected on Sensor Input 7.

Bit 5 - CS6 - Indicates that a touch was detected on Sensor Input 6.

Bit 4 - CS5 - Indicates that a touch was detected on Sensor Input 5.

Bit 3 - CS4 - Indicates that a touch was detected on Sensor Input 4.

Bit 2 - CS3 - Indicates that a touch was detected on Sensor Input 3.

Bit 1 - CS2 - Indicates that a touch was detected on Sensor Input 2. This sensor input can be linked to LED2.

Bit 0 - CS1 - Indicates that a touch was detected on Sensor Input 1. This sensor input can be linked to LED1.

6.2.3

LED STATUS - 04H

The LED Status Registers indicate when an LED has completed its configured behavior (see Section 6.31, "LED Behav-

ior Register") after being actuated by the host (see Section 6.28, "LED Output Control Register"). These bits are ignored

when the LED is linked to a capacitive sensor input. All LED Status bits are cleared when the INT bit is cleared.

Bit 1 - LED2_DN - Indicates that LED2 has finished its behavior after being actuated by the host.

Bit 0 - LED1_DN - Indicates that LED1 has finished its behavior after being actuated by the host.

6.3

Noise Flag Status Registers

The Noise Flag Status registers store status bits that are generated from the analog block if the detected noise is above

the operating region of the analog detector or the RF noise detector. These bits indicate that the most recently received

data from the sensor input is invalid and should not be used for touch detection. So long as the bit is set for a particular

channel, the delta count value is reset to 00h and thus no touch is detected.

These bits are not sticky and will be cleared automatically if the analog block does not report a noise error.

APPLICATION NOTE: If the MTP detection circuitry is enabled, these bits count as sensor inputs above the MTP

threshold (see Section 5.5.4, "Multiple Touch Pattern Detection") even if the corresponding

delta count is not. If the corresponding delta count also exceeds the MTP threshold, it is not

counted twice.

APPLICATION NOTE: Regardless of the state of the Noise Status bits, if low frequency noise is detected on a

sensor input, that sample will be discarded unless the DIS_ANA_NOISE bit is set. As well,

if RF noise is detected on a sensor input, that sample will be discarded unless the

DIS_RF_NOISE bit is set.

TABLE 6-5:

NOISE FLAG STATUS REGISTERS

ADDR

R/W

Default

0Ah

Noise Flag Status

CS8_

NOISE

CS7_

NOISE

CS6_

NOISE

CS5_

NOISE

CS4_

NOISE

CS3_

NOISE

CS2_

NOISE

CS1_

NOISE

00h

CAP1128 Datasheet(PDF) 33 Page - Microchip Technology

CAP1128 Datasheet(HTML) 33 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

Datasheet Download

Link URL