COP684FH datasheet(19/49 Pages) NSC

19 / 49 page

Power Save Modes (Continued)

tion (since CKO becomes a dedicated output), and so may

be used with an RC clock configuration. The third method of

exiting the HALT mode is by pulling the RESET pin low.

Since a crystal or ceramic resonator may be selected as the

oscillator, the Wakeup signal is not allowed to start the chip

running immediately since crystal oscillators and ceramic

resonators have a delayed start up time to reach full ampli-

tude and frequency stability. The IDLE timer is used to gen-

erate a fixed delay to ensure that the oscillator has indeed

stabilized before allowing instruction execution. In this case,

upon detecting a valid Wakeup signal, only the oscillator cir-

cuitry is enabled. The IDLE timer is loaded with a value of

256 and is clocked with the t

c instruction cycle clock. The tc

clock is derived by dividing the oscillator clock down by a fac-

tor of 10. The Schmitt trigger following the CKI inverter on

the chip ensures that the IDLE timer is clocked only when the

oscillator has a sufficiently large amplitude to meet the

Schmitt trigger specifications. This Schmitt trigger is not part

of the oscillator closed loop. The startup timeout from the

IDLE timer enables the clock signals to be routed to the rest

of the chip.

If an RC clock option is being used, the fixed delay is intro-

duced optionally. A control bit, CLKDLY, mapped as configu-

ration bit G7, controls whether the delay is to be introduced

or not. The delay is included if CLKDLY is set, and excluded

if CLKDLY is reset. The CLKDLY bit is cleared on reset.

The device has two mask options associated with the HALT

mode. The first mask option enables the HALT mode feature,

while the second mask option disables the HALT mode. With

the HALT mode enable mask option, the device will enter

and exit the HALT mode as described above. With the HALT

disable mask option, the device cannot be placed in the

HALT mode (writing a “1” to the HALT flag will have no effect,

the HALT flag will remain “0”).

IDLE MODE

The device is placed in the IDLE mode by writing a “1” to the

IDLE flag (G6 data bit). In this mode, all activities, except the

associated on-board oscillator circuitry, and the IDLE Timer

T0, are stopped.

The power supply requirements of the microcontroller in this

mode of operation are typically around 30% of normal power

requirement of the microcontroller.

As with the HALT mode, the device can be returned to nor-

mal operation with a reset, or with a Multi-Input Wakeup from

the L Port. Alternately, the microcontroller resumes normal

operation from the IDLE mode when the thirteenth bit (repre-

senting 4.096 ms at internal clock frequency of 1 MHz, t

c =

1 µs) of the IDLE Timer toggles.

This toggle condition of the thirteenth bit of the IDLE Timer

T0 is latched into the T0PND pending flag.

The user has the option of being interrupted with a transition

on the thirteenth bit of the IDLE Timer T0. The interrupt can

be enabled or disabled via the T0EN control bit. Setting the

T0EN flag enables the interrupt and vice versa.

The user can enter the IDLE mode with the Timer T0 inter-

rupt enabled. In this case, when the T0PND bit gets set, the

device will first execute the Timer T0 interrupt service routine

and then return to the instruction following the “Enter Idle

Mode” instruction.

Alternatively, the user can enter the IDLE mode with the

IDLE Timer T0 interrupt disabled. In this case, the device will

resume normal operation with the instruction immediately

following the “Enter IDLE Mode” instruction.

Note: It is necessary to program two NOP instructions following both the set

HALT mode and set IDLE mode instructions. These NOP instructions

are necessary to allow clock resynchronization following the HALT or

IDLE modes.

Multi-Input Wakeup

The Multi-Input Wakeup feature is ued to return (wakeup) the

device from either the HALT or IDLE modes. Alternately

Multi-Input Wakeup/Interrupt feature may also be used to

generate up to 8 edge selectable external interrupts.

Figure 11 shows the Multi-Input Wakeup logic.

COP684FH Datasheet(PDF) 19 Page - National Semiconductor (TI)

COP684FH Datasheet(HTML) 19 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

Datasheet Download

Link URL