COP684FH datasheet(20/49 Pages) NSC

20 / 49 page

Multi-Input Wakeup (Continued)

The Multi-Input Wakeup feature utilizes the L Port. The user

selects which particular L port bit (or combination of L Port

bits) will cause the device to exit the HALT or IDLE modes.

The selection is done through the Reg: WKEN. The Reg:

WKEN is an 8-bit read/write register, which contains a con-

trol bit for every L port bit. Setting a particular WKEN bit en-

ables a Wakeup from the associated L port pin.

The user can select whether the trigger condition on the se-

lected L Port pin is going to be either a positive edge (low to

high transition) or a negative edge (high to low transition).

This selection is made via the Reg: WKEDG, which is an

8-bit control register with a bit assigned to each L Port pin.

Setting the control bit will select the trigger condition to be a

negative edge on that particular L Port pin. Resetting the bit

selects the trigger condition to be a positive edge. Changing

an edge select entails several steps in order to avoid a

pseudo Wakeup condition as a result of the edge change.

First, the associated WKEN bit should be reset, followed by

the edge select change in WKEDG. Next, the associated

WKPND bit should be cleared, followed by the associated

WKEN bit being re-enabled.

An example may serve to clarify this procedure. Suppose we

wish to change the edge select from positive (low going high)

to negative (high going low) for L Port bit 5, where bit 5 has

previously been enabled for an input interrupt. The program

would be as follows:

RBIT

5, WKEN

; Disable MIWN

SBIT

5, WKEDG

; Change edge polarity

RBIT

5, WKPND

; Reset pending flag

SBIT

5, WKEN

; Enable MIWU

If the L port bits have been used as outputs and then

changed to inputs with Multi-Input Wakeup/Interrupt, a safety

procedure should also be followed to avoid inherited pseudo

wakeup conditions. After the selected L port bits have been

changed from output to input but before the associated

WKEN bits are enabled, the associated edge select bits in

WKEDG should be set or reset for the desired edge selects,

followed by the associated WKPND bits being cleared.

This same procedure should be used following reset, since

the L port inputs are left floating as a result of reset.

The occurrence of the selected trigger condition for

Multi-Input Wakeup is latched into a pending register called

WKPND. The respective bits of the WKPND register will be-

set on the occurrence of the selected trigger edge on the cor-

responding Port L pin. The user has the responsibility of

clearing these pending flags. Since WKPND is a pending

the device will not enter the HALT mode if any Wakeup bit is

both enabled and pending. Consequently, the user has the

responsibility of clearing the pending flags before attempting

to enter the HALT mode.

WKEN, WKPND and WKEDG are all read/write registers,

and are cleared at reset.

PORT L INTERRUPTS

Port L provides the user with an additional eight fully select-

able, edge sensitive interrupts which are all vectored into the

same service subroutine.

The interrupt from Port L shares logic with the wake up cir-

cuitry. The register WKEN allows interrupts from Port L to be

individually enabled or disabled. The register WKEDG speci-

fies the trigger condition to be either a positive or a negative

edge. Finally, the register WKPND latches in the pending

trigger conditions.

The GIE (Global Interrupt Enable) bit enables the interrupt

function.

A control flag, LPEN, functions as a global interrupt enable

for Port L interrupts. Setting the LPEN flag will enable inter-

DS012602-15

0 = low going high

↑

1 = high going low

↓

FIGURE 11. Multi-Input Wake Up Logic

COP684FH Datasheet(PDF) 20 Page - National Semiconductor (TI)

COP684FH Datasheet(HTML) 20 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

Datasheet Download

Link URL