RN41 datasheet(15/28 Pages) MICROCHIP

15 / 28 page

 2014 Microchip Technology Inc.

DS50002280A-page 15

RN41/RN41N

The Industry Canada certification label of a module

shall be clearly visible at all times when installed in the

host device, otherwise the host device must be labeled

to display the Industry Canada certification number of

the module, preceded by the words “Contains transmit-

ter module”, or the word “Contains”, or similar wording

expressing the same meaning, as follows:

User Manual Notice for License-Exempt Radio Appara-

tus (from Section 7.1.3 RSS-Gen, Issue 3, December

2010): User manuals for license-exempt radio appara-

tus shall contain the following or equivalent notice in a

conspicuous location in the user manual or alterna-

tively on the device or both:

Transmitter Antenna (from Section 7.1.2 RSS-Gen,

Issue 3, December 2010): User manuals for transmit-

ters shall display the following notice in a conspicuous

location:

The above notice may be affixed to the device instead

of displayed in the user manual.

3.2.2

RF EXPOSURE

All transmitters regulated by IC must comply with RF

exposure requirements listed in RSS-102 - Radio Fre-

quency (RF) Exposure Compliance of Radiocommuni-

cation Apparatus (All Frequency Bands).

3.2.3

APPROVED EXTERNAL ANTENNA

TYPES

Transmitter Antenna (from Section 7.1.2 RSS-Gen,

Issue 3, December 2010):

The RN41N module can only be sold or operated with

antennas with which it was approved. Transmitter may

be approved with multiple antenna types. An antenna

type comprises antennas having similar in-band and

out-of-band radiation patterns. Testing shall be per-

formed using the highest gain antenna of each combi-

nation of transmitter and antenna type for which

approval is being sought, with the transmitter output

power set at the maximum level. Any antenna of the

same type having equal or lesser gain as an antenna

that had been successfully tested with the transmitter,

will also be considered approved with the transmitter,

and may be used and marketed with the transmitter.

When a measurement at the antenna connector is

used to determine RF output power, the effective gain

of the device's antenna shall be stated, based on mea-

surement or on data from the antenna manufacturer.

For transmitters of output power greater than 10 milli-

watts, the total antenna gain shall be added to the mea-

sured RF output power to demonstrate compliance to

the specified radiated power limits.

Approved external antenna types for the RN41N mod-

ule are listed in Table 2-3.

3.2.4

HELPFUL WEB SITES

Industry Canada: http://www.ic.gc.ca/

3.3

Europe

The RN41/RN41N module is an R&TTE Directive

assessed radio module that is CE marked and has

been manufactured and tested with the intention of

being integrated into a final product.

The RN41/RN41N module has been tested to R&TTE

Directive 1999/5/EC Essential Requirements for Health

and Safety (Article (3.1(a)), Electromagnetic Compati-

bility (EMC) (Article 3.1(b)), and Radio (Article 3.2) and

are summarized in Table 3-1: European Compliance

Testing. A Notified Body Opinion has also been issued.

All test reports are available on the RN41/RN41N prod-

uct web page at http://www.microchip.com.

RN-41:

Contains transmitter module IC: 6514A-RN413

RN-41N:

Contains transmitter module IC: 7693A-RN41N

This device complies with Industry Canada license-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not

cause interference, and (2) this device must accept

any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Indus-

trie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux con-

ditions suivantes: (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit

accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d'en compromettre le

fonctionnement.

Under Industry Canada regulations, this radio trans-

mitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the trans-

mitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotrop-

ically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.

Conformément à la réglementation d'Industrie Can-

ada, le présent émetteur radio peut fonctionner avec

une antenne d'un type et d'un gain maximal (ou

inférieur) approuvé pour l'émetteur par Industrie Can-

ada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il

faut choisir le type d'antenne et son gain de sorte

que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à

l'établissement d'une communication satisfaisante.

RN41 Datasheet(PDF) 15 Page - Microchip Technology

RN41 Datasheet(HTML) 15 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Datasheet Download

Link URL