| Electronic Components Datasheet Search |
|
AD9254 Datasheet(PDF) 18 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD9254 Datasheet(HTML) 18 Page - Analog Devices |
|
18 / 41 page ![]() AD9254 Rev. 0 | Page 17 of 40 VREF SENSE 0.5V AD9254 REFT REFB SELECT LOGIC 0.1µF 0.1µF 0.1µF VIN– VIN+ ADC CORE Figure 37. Internal Reference Configuration VREF SENSE 0.5V AD9254 VIN– VIN+ REFT REFB SELECT LOGIC 0.1µF 0.1µF R2 R1 0.1µF ADC CORE Figure 38. Programmable Reference Configuration If the internal reference of the AD9254 is used to drive multiple converters to improve gain matching, the loading of the reference by the other converters must be considered. Figure 39 depicts how the internal reference voltage is affected by loading. 0 –1.25 02.0 LOAD CURRENT (mA) –0.25 –0.50 –0.75 –1.00 0.5 1.0 1.5 VREF = 0.5V VREF = 1V Figure 39. VREF Accuracy vs. Load External Reference Operation The use of an external reference may be necessary to enhance the gain accuracy of the ADC or improve thermal drift characteristics. Figure 40 shows the typical drift characteristics of the internal reference in both 1 V and 0.5 V modes. –40 –20 10 0 TEMPERATURE (°C) 8 6 4 2 80 0 204060 VREF = 1V VREF = 0.5V Figure 40. Typical VREF Drift When the SENSE pin is tied to AVDD, the internal reference is disabled, allowing the use of an external reference. An internal resistor divider loads the external reference with an equivalent 6 kΩ load (see Figure 11). In addition, an internal buffer generates the positive and negative full-scale references for the ADC core. Therefore, the external reference must be limited to a maximum of 1 V. CLOCK INPUT CONSIDERATIONS For optimum performance, the AD9254 sample clock inputs (CLK+ and CLK−) should be clocked with a differential signal. The signal is typically ac-coupled into the CLK+ pin and the CLK− pin via a transformer or capacitors. These pins are biased internally (see Figure 5) and require no external bias. Clock Input Options The AD9254 has a very flexible clock input structure. The clock input can be a CMOS, LVDS, LVPECL, or sine wave signal. Regardless of the type of signal used, the jitter of the clock source is of the most concern, as described in the Jitter Considerations section. Figure 41 shows one preferred method for clocking the AD9254. A low jitter clock source is converted from single- ended to a differential signal using an RF transformer. The back-to-back Schottky diodes across the transformer secondary limit clock excursions into the AD9254 to approximately 0.8 V p-p differential. This helps prevent the large voltage swings of the clock from feeding through to other portions of the AD9254, while preserving the fast rise and fall times of the signal, which are critical to a low jitter performance. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |