Electronic Components Datasheet Search
  English  ▼

X  

AD9254 Datasheet(PDF) 20 Page - Analog Devices

Part # AD9254
Description  Analog-to-Digital Converter
PDF  41 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD9254 Datasheet(HTML) 20 Page - Analog Devices

Back Button AD9254 Datasheet HTML 16Page - Analog Devices AD9254 Datasheet HTML 17Page - Analog Devices AD9254 Datasheet HTML 18Page - Analog Devices AD9254 Datasheet HTML 19Page - Analog Devices AD9254 Datasheet HTML 20Page - Analog Devices AD9254 Datasheet HTML 21Page - Analog Devices AD9254 Datasheet HTML 22Page - Analog Devices AD9254 Datasheet HTML 23Page - Analog Devices AD9254 Datasheet HTML 24Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 20 / 41 page
background image
AD9254
Rev. 0 | Page 19 of 40
The DCS can be enabled or disabled by setting the SDIO/DCS
pin when operating in the external pin mode (see Table 10), or
via the SPI, as described in Table 13.
Table 10. Mode Selection (External Pin Mode)
Voltage at Pin
SCLK/DFS
SDIO/DCS
AGND
Binary (default)
DCS disabled
AVDD
Twos complement
DCS enabled
(default)
JITTER CONSIDERATIONS
High speed, high resolution ADCs are sensitive to the quality of
the clock input. The degradation in SNR at a given input
frequency (fIN) due to jitter (tJ) is calculated as follows:
SNR = −20 log (2π × fIN × tJ)
In the equation, the rms aperture jitter represents the root mean
square of all jitter sources, which include the clock input, analog
input signal, and ADC aperture jitter specification. IF under-
sampling applications are particularly sensitive to jitter, as
shown in Figure 46.
75
70
65
60
55
50
45
40
1
10
100
1000
INPUT FREQUENCY (MHz)
3.00ps
0.05ps
MEASURED
PERFORMANCE
0.20ps
0.5ps
1.0ps
1.50ps
2.00ps
2.50ps
Figure 46. SNR vs. Input Frequency and Jitter
Treat the clock input as an analog signal in cases where aperture
jitter can affect the dynamic range of the AD9254. Power supplies
for clock drivers should be separated from the ADC output
driver supplies to avoid modulating the clock signal with digital
noise. The power supplies should also not be shared with analog
input circuits, such as buffers, to avoid the clock modulating onto
the input signal or vice versa. Low jitter, crystal-controlled oscil-
lators make the best clock sources. If the clock is generated from
another type of source (by gating, dividing, or other methods),
it should be retimed by the original clock at the last step.
Refer to Application Notes AN-501, Aperture Uncertainty and
ADC System Performance; and AN-756, Sampled Systems and
the Effects of Clock Phase Noise and Jitter, for more in-depth
information about jitter performance as it relates to ADCs.
POWER DISSIPATION AND STANDBY MODE
The power dissipated by the AD9254 is proportional to its sample
rate (see Figure 47). The digital power dissipation is determined
primarily by the strength of the digital drivers and the load on each
output bit. Maximum DRVDD current (IDRVDD) can be calculated as
N
f
C
V
I
CLK
LOAD
DRVDD
DRVDD
×
×
×
=
2
where N is the number of output bits, 14 in the AD9254.
This maximum current occurs when every output bit switches
on every clock cycle, that is, a full-scale square wave at the
Nyquist frequency, fCLK/2. In practice, the DRVDD current is
established by the average number of output bits switching,
which is determined by the sample rate and the characteristics
of the analog input signal. Reducing the capacitive load
presented to the output drivers can minimize digital power
consumption. The data in Figure 47 was taken under the same
operating conditions as the data for the Typical Performance
Characteristics section, with a 5 pF load on each output driver.
500
480
460
440
420
400
380
360
340
320
300
300
250
200
150
100
50
0
0
1020 30405060708090 100 110 120 130 140 150
CLOCK FREQUENCY (MHz)
POWER
I (AVDD)
I (DRVDD)
Figure 47. AD9254 Power and Current vs. Clock Frequency fIN = 30 MHz
Power-Down Mode
By asserting the PDWN pin high, the AD9254 is placed in power-
down mode. In this state, the ADC typically dissipates 1.8 mW.
During power-down, the output drivers are placed in a high
impedance state. Reasserting the PDWN pin low returns the
AD9254 to its normal operational mode. This pin is both 1.8 V
and 3.3 V tolerant.
Low power dissipation in power-down mode is achieved by
shutting down the reference, reference buffer, biasing networks,
and clock. The decoupling capacitors on REFT and REFB are
discharged when entering power-down mode and then must be
recharged when returning to normal operation. As a result, the
wake-up time is related to the time spent in power-down mode;
and shorter power-down cycles result in proportionally shorter
wake-up times. With the recommended 0.1 μF decoupling capaci-
tors on REFT and REFB, it takes approximately 0.25 ms to fully
discharge the reference buffer decoupling capacitors and 0.35 ms to
restore full operation.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com