Electronic Components Datasheet Search
  English  ▼

X  

SA2102DSA Datasheet(PDF) 7 Page - Sames

Part # SA2102DSA
Description  Reference Meter
PDF  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  SAMES [Sames]
Direct Link  http://www.sames.co.za
Logo SAMES - Sames

SA2102DSA Datasheet(HTML) 7 Page - Sames

Back Button SA2102DSA Datasheet HTML 3Page - Sames SA2102DSA Datasheet HTML 4Page - Sames SA2102DSA Datasheet HTML 5Page - Sames SA2102DSA Datasheet HTML 6Page - Sames SA2102DSA Datasheet HTML 7Page - Sames SA2102DSA Datasheet HTML 8Page - Sames SA2102DSA Datasheet HTML 9Page - Sames SA2102DSA Datasheet HTML 10Page - Sames SA2102DSA Datasheet HTML 11Page - Sames Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 16 page
background image
sames
RM2102DSE
15/16
http://www.sames.co.za
7/16
http://www.sames.co.za
PRELIMINARY
Table 5: IEC 61036 Specifications
Current Value
0.2Ib
I < Imax
£
0.2Ib
I < Imax
£
0.1Ib
I < 0.2Ib
£
0.1Ib
I < 0.2Ib
£
0.1Ib
I
Imax
££
0.05Ib
I < 0.1Ib
£
Power Factor
0.8 capacitive
0.5 inductive
0.8 capacitive
0.5 inductive
1
1
Percentage Error Limits
± 1.0%
± 1.0%
± 1.5%
± 1.5%
± 1.0%
± 1.5%
Class 1
N/A
± 2.0%
N/A
± 2.5%
± 2.0%
± 2.5%
Class 2
PCB DESIGN CONSIDERATIONS
There are numerous PCB design aspects to consider when
designing a power/energy meter, but only a few crucial
aspects will be discussed here.
1. The sense resistors on the current input (R15 and R16)
must be located as close to the SA2102D-input pins as
possible. This also holds true for the 1M
resistor (R18),
and the biasing resistor (R17). 2. T h e
s upply
bypass
capacitors C4, C5 and C6 must be positioned as close as
possible to the supply pins of the SA2102D, and
connected to a solid ground plane.
3. It is advisable to keep the ground plane surrounding the
device clear of noise that may influence the sensing
signals.
4. Make use of two different ground planes. The one plane
should be used only for the analog section of the PCB, the
other containing the power supply and digital signals.
5. The analog ground plane must be kept as quiet as
possible, i.e. free from high frequency signals, and away
from high voltages and currents.
6. For EMC considerations, the two ground planes must only
be connected at one point, preferably at the device ground
pin. These two planes can also be connected via a ferrite
bead that will help to suppress transients and high
frequency interference from the digital to the analog plane.
7. The power supply routing and placement is also a very
important aspect to consider. The power supply must be
placed as far away from the analog side of the device as
possible, so as not to interfere with the sensing functions.
The routing must be done in such a way that all other
jumpers and devices are serviced before the SA2102D
W
device. This will ensure that all the noise (spikes and power
demands) are put on the supply line before it gets to the
device. Most of the noise will then be filtered out by the
supply bypass capacitors that are situated as close as
possible to the device.
8. The meter is protected from high transients on the main
voltage input by means of a
etal
xide
aristor. These
MOVs will clamp high transients with a sufficiently long rise
time when measured with respect to neutral.
1. The onboard power supply consists of a simple capacitive
divider configuration. Where the output voltage is rectified
by a diode pair, and held constant by means of a pair of
TL431 shunt regulators.
2. The maximum current available from the supply is
approximately 20mA.
MO
V
Power supply
3. Please take note that the meter is fitted with a
470nF/250VAC X3 type capacitor for 220VAC mains
supply. This capacitor must be changed to 1µF/150VAC X3
type when the mains supply voltage is changed to a
110VAC network.
Figure 6 shows the schematic of the complete meter design.
This meter is designed to meet the IEC 61036 accuracy
requirements for a Class 1 meter. The IEC specifications are
summarized in table 5.
DESIGN RESULTS



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com