Electronic Components Datasheet Search
  English  ▼

X  

LTC3882 Datasheet(PDF) 13 Page - Analog Devices

Part # LTC3882
Description  60V Dual Output Step-Up Controller with Digital Power System Management
PDF  116 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

LTC3882 Datasheet(HTML) 13 Page - Analog Devices

Back Button LTC3882 Datasheet HTML 9Page - Analog Devices LTC3882 Datasheet HTML 10Page - Analog Devices LTC3882 Datasheet HTML 11Page - Analog Devices LTC3882 Datasheet HTML 12Page - Analog Devices LTC3882 Datasheet HTML 13Page - Analog Devices LTC3882 Datasheet HTML 14Page - Analog Devices LTC3882 Datasheet HTML 15Page - Analog Devices LTC3882 Datasheet HTML 16Page - Analog Devices LTC3882 Datasheet HTML 17Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 116 page
background image
LTC7880
13
Rev 0
For more information www.analog.com
PIN FUNCTIONS
SW0/SW1 (Pins 1, 39): Switch Node Connections to
Inductors. Voltage swings at the pins are from a diode
voltage drop below ground to a diode voltage drop above
VOUT.
TG0/TG1 (Pins 2, 38): Top Gate Driver Outputs. These are
the outputs of floating drivers with a voltage swing equal
to DRVCC superimposed on the switch node voltages.
VSENSE1+/VSENSE0+ (Pins 3, 45): Positive Output Voltage
Sense Inputs.
ISENSE0+/ISENSE1+ (Pins 4, 9): Current Sense Comparator
Inputs. The (+) input to the current comparator is con-
nected to the input voltage.
ISENSE0–/ISENSE1–(Pins5,10):CurrentSenseComparator
Inputs. The (–) input to the current comparator is normally
connected to the DCR sensing network or current sensing
resistor.
TSNS0/TSNS1 (Pins 6, 36): External Diode Temperature
Sense. Connect to the anode of a diode-connected PNP
transistor in order to sense remote temperature. Directly
connect the cathode using a seperate ground return path
to Pin 53 of the LTC7880. A bypass capacitor between the
anodeandcathodemustbelocatedincloseproximitytothe
transistor. If external temperature sense elements are not
installed,shortpintogroundandsettheUT_FAULT_LIMIT
to –275°C and the UT_FAULT_RESPONSE to ignore.
VIN0+/VIN1+ (Pins 7, 35): Input Voltage Sense Inputs.
NC (Pin 8): No Connection.
ITHR0/ITHR1 (Pins 11, 32): Loop Compensation Nodes.
ITH0/ITH1 (Pins 12, 31): Current Control Threshold and
Error Amplifier Compensation Nodes. Each associated
channel’scurrentcomparatortrippingthresholdincreases
with its ITH voltage.
SYNC (Pin 13): External Clock Synchronization Input and
Open-Drain Output Pin. If an external clock is present at
this pin, the switching frequency will be synchronized to
the external clock. If clock master mode is enabled, this
pin will pull low at the switching frequency with a 500ns
pulsewidthtoground.Aresistorpull-upto3.3Visrequired
in the application.
SCL (Pin 14): Serial Bus Clock Input. Open-drain output,
can hold the output low if clock stretching is enabled. A
pull-up resistor to 3.3V is required in the application.
SDA (Pin 15): Serial Bus Data Input and Output. A pull-up
resistor to 3.3V is required in the application.
ALERT (Pin 16): Open-Drain Digital Output. Connect the
SMBALERT signal to this pin. A pull-up resistor to 3.3V
is required in the application.
FAULT0/FAULT1 (Pins 17, 18): Digital Programmable
General Purpose Inputs and Outputs. Open-drain output.
A pull-up resistor to 3.3V is required in the application.
RUN0/RUN1 (Pins 19, 20): Enable Run Input and Output.
Logic high on this pin enables the controller. Open-drain
output holds the pin low until the LTC7880 is out of reset.
This pin should be driven by an open-drain digital output.
A pull-up resistor to 3.3V is required in the application.
ASEL0/ASEL1 (Pin 21/Pin 22): Serial Bus Address Select
Inputs. Connect optional 1% resistor dividers between
VDD25 and GND to these pins to select the serial bus
interface address. Refer to the Applications Information
section for more detail. Minimize capacitance when the
pin is open to assure accurate detection of the pin state.
VOUT0_CFG/VOUT1_CFG (Pins 23, 24): Output Voltage
Select Pins. Connect a ±1% resistor divider between the
chip VDD25, VOUT_CFG and GND in order to select output
voltage. If the pin is left open, the IC will use the value
programmed in the EEPROM. Refer to the Applications
Information section for more detail. Minimize capacitance
when the pin is open to assure accurate detection of the
pin state.
FREQ_CFG (Pin 25): Frequency Select Pin. Connect a
±1% resistor divider between the chip VDD25 FREQ_CFG
and GND in order to select switching frequency. If the pin
is left open, the IC will use the value programmed in the
EEPROM. Refer to the Applications Information section
for more detail. Minimize capacitance when the pin is open
to assure accurate detection of the pin state.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com