Electronic Components Datasheet Search
  English  ▼

X  

LTC3882 Datasheet(PDF) 21 Page - Analog Devices

Part # LTC3882
Description  60V Dual Output Step-Up Controller with Digital Power System Management
PDF  116 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

LTC3882 Datasheet(HTML) 21 Page - Analog Devices

Back Button LTC3882 Datasheet HTML 17Page - Analog Devices LTC3882 Datasheet HTML 18Page - Analog Devices LTC3882 Datasheet HTML 19Page - Analog Devices LTC3882 Datasheet HTML 20Page - Analog Devices LTC3882 Datasheet HTML 21Page - Analog Devices LTC3882 Datasheet HTML 22Page - Analog Devices LTC3882 Datasheet HTML 23Page - Analog Devices LTC3882 Datasheet HTML 24Page - Analog Devices LTC3882 Datasheet HTML 25Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 21 / 116 page
background image
LTC7880
21
Rev 0
For more information www.analog.com
OPERATION
SWITCHING FREQUENCY AND PHASE
The switching frequency of the PWM can be established
with an internal oscillator or an external time base. The
internal phase-locked loop (PLL) synchronizes PWM
control to this timing reference with proper phase rela-
tion, whether the clock is provided internally or externally.
The device can also be configured to provide the master
clock to other ICs through PMBus command, EEPROM
setting, or external configuration resistors as outlined in
Tables 4 and 5.
As clock master, the LTC7880 will drive its open-drain
SYNC pin at the selected rate with a pulse width of 500ns.
An external pull-up resistor between SYNC and VDD33
is required in this case. Only one device connected to
SYNC should be designated to drive the pin. If multiple
LTC7880s programmed as clock masters are wired to the
same SYNC line with a pull-up resistor, just one of the
devices is automatically elected to provide clocking, and
the others disable their SYNC outputs.
The LTC7880 will automatically accept an external
SYNC input, disabling its own SYNC drive if necessary.
Whether configured to drive SYNC or not, the LTC7880
can continue PWM operation using its own internal
oscillator if an external clock signal is subsequently lost.
The device can also be programmed to always require
an external oscillator for PWM operation by setting bit 4
of MFR_CONFIG_ALL_LTC7880. The status of the SYNC
driver circuit is indicated by bit 10 of MFR_PADS.
The MFR_PWM_CONFIG_LTC7880 command can be
usedtoconfigurethephaseofeachchannel.Desiredphase
can also be set from EEPROM or external configuration
resistors as outlined in Table 5. Designated phase is
the relationship between the falling edge of SYNC and
the internal clock edge that sets the PWM latch to turn
on the top power switch. Additional small propagation
delays to the PWM control pins will also apply. Both
channels must be off before the FREQUENCY_SWITCH
and MFR_PWM_CONFIG_LTC7880 commands can be
written to the LTC7880.
The phase relationships and frequency are independent
of each other, providing numerous application options.
Multiple LTC7880 ICs can be synchronized to realize
a PolyPhase array. In this case the phases should be
separated by 360/n degrees, where n is the number of
phases driving the output voltage rail.
OUTPUT VOLTAGE SENSING
In high and low range, both the channel 0 sense pin
(VSENSE0+) and channel 1 sense pin (VSENSE1+) are refer-
enced to GND. The (telemetry) ADC is fully differential and
makes measurements of channels 0 and 1 output voltages
at the VSENSE0/GND and VSENSE1/GND pins, respectively.
OUTPUT CURRENT SENSING
To sense the total output current of the the power stage, a
sense resistor is placed between the IOUT+ and IOUT– pins
which are connected at the output of the power stage
The filtered voltage is amplified by the internal high side
current sense amplifier and digitized by the LTC7880’s
telemetry ADC. The maximum differential sense voltage
is 50mV. The LTC7880 computes the input current using
the R value stored in the IOUT_CAL_GAIN command. The
resulting measured powerstage current is returned by the
READ_IOUT command.
INPUT CURRENT SENSING
The input current is sensed by the LTC7880 at the ISENSE0+
/ISENSE0- and ISENSE1+ /ISENSE1- pins. The LTC7880 sup-
ports RSENSE or inductor DCR current sensing. Refer to
the Low Value Resistor Current Sensing and Inductor DCR
Current Sensing subsections in the Applications Informa-
tion section for further details.
PolyPhase LOAD SHARING
Multiple LTC7880’s can be connected in parallel in order
to provide a balanced load-share solution by connecting
the necessary pins. Figure 3 illustrates the shared con-
nections required for load sharing.
The SYNC pin should only be enabled on one of the
LTC7880s. The other(s) should be programmed to dis-
able SYNC with the oscillator frequency set to the nominal
value. When bit[7] of the MFR_PWM_CONFIG command
is set, Channel 1 will use the feedback node of Chan-



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com