| Electronic Components Datasheet Search |
|
89C535 Datasheet(PDF) 26 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
89C535 Datasheet(HTML) 26 Page - NXP Semiconductors |
|
26 / 35 page ![]() Philips Semiconductors Preliminary specification 89C535/89C536/89C538 CMOS single-chip 8-bit microcontrollers with FLASH program memory 1997 Jun 05 26 System Considerations During the switch between active and standby conditions, transient current peaks are produced on the rising and falling edges of Chip Enable. The magnitude of these transient current peaks is dependent on the output capacitance loading of the device. At a minimum, a 0.1uF ceramic capacitor (high frequency, low inherent inductance) should be used on each device between VCC and GND, and between VPP and GND to minimize transient effects. SYMBOL PARAMETER MIN TYP MAX UNIT CONDITION CIN VPPH 14 PF VIN = 0V COUT VPPH 16 pF VOUT = 0V Command programming/Data programming/Erase Operation DC CHARACTERISTICS Tamb = 0°C to 70°C, VCC = 5V ± 10%, VPP = 12.0V ± 5% SYMBOL PARAMETER CONDITION MIN TYP MAX UNIT ILI Input Leakage Current VIN = GND to VCC 10 µA ILO Output Leakage Current VOUT = GND to VCC 10 µA ISB1 Standby VCC Current CE = VIH 1 mA ISB2 CE = VCC ± 0.3 V 1 100 µA ICC1 (Read) Operating VCC Current IOUT = 0 mA, f=1 MHz 30 mA ICC2 IOUT = 0 mA, F=11MHz 50 mA ICC3 (Program) In Programming 50 mA ICC4 (Erase) In Erase 50 mA ICC5 (Program Verify) In Program Verify 50 mA ICC6 (Erase Verify) In erase Verify 50 mA IPP1 (Read) VPP Current VPP=12.6 V 100 µA IPP2 (Program) In Programming 50 mA IPP3 (Erase) In Erase 50 mA IPP4 (Program Verify) In Program Verify 50 mA IPP5 (Erase Verify) In Erase Verify 50 mA VIL Input Voltage –0.5 (Note 5) 0.2VPP – 0.3 V VIH 2.4 VCC+0.3V V (Note 6) VOL Output Voltage Low IOL=2.1mA 0.45 V VOH Output Voltage High IOH=400uA 2.4 V NOTES: 1. VCC must be applied before VPP and removed after VPP. 2. VPP must not exceed 14V including overshoot. 3. An influence may be had upon device reliability if the device is installed or removed while VPP=12V. 4. Do not alter VPP from VIL to 12V or 12V to VIL when CE=VIL 5. VIL min. = –0.5V for pulse width ≤ 20ns. 6. If VIH is over the specified maximum value, programming operation cannot be guaranteed. 7. All currents are in RMS unless otherwise noted. (Sampled, not 100% tested.). |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |