| Electronic Components Datasheet Search |
|
AD9910 Datasheet(PDF) 5 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD9910 Datasheet(HTML) 5 Page - Analog Devices |
|
5 / 13 page ![]() PRELIMINARY TECHNICAL DATA AD9910 Rev. PrD| Page 5 of 13 Parameter Min Typ Max Unit Serial Control Bus Maximum Frequency 25 Mbps Minimum Clock Pulse Width Low 7 ns Minimum Clock Pulse Width High 8 ns Maximum Clock Rise/Fall Time 2 ns Minimum Data Setup Time 3 ns Minimum Data Hold Time 0 ns Maximum Data Valid Time 25 ns Wake-Up Time2 1 ms Minimum Reset Pulse Width High 5 SYSCLK Cycles3 I/O UPDATE, PS0, PS1 to SYNCCLK Setup Time 4 ns I/O UPDATE, PS0, PS1 to SYNCCLK Hold Time 1 ns Parallel Data Bus Maximum Frequency 250 Mword/sec Data setup time (to PDCLK) TBD nsec Data hold time (to PDCLK) TBD nsec Latency I/O UPDATE to Frequency Change Prop Delay TBD SYSCLK Cycles I/O UPDATE to Phase Offset Change Prop Delay TBD SYSCLK Cycles I/O UPDATE to Amplitude Change Prop Delay TBD SYSCLK Cycles CMOS LOGIC INPUTS Logic 1 Voltage @ DVDD_I/O (Pin 43) = 3.3 V 2.2 V Logic 0 Voltage @ DVDD_I/O (Pin 43) = 3.3 V 0.8 V Logic 1 Current 3 12 µA Logic 0 Current 12 µA Input Capacitance 2 pF CMOS LOGIC OUTPUTS (1 mA Load) Logic 1 Voltage 2.8 V Logic 0 Voltage 0.4 V POWER CONSUMPTION Single Tone Mode 700 TBD mW With RAM or Linear Sweep Enabled 800 TBD mW Rapid Power-Down Mode 500 TBD mW Full-Sleep Mode 50 TBD mW SYNCHRONIZATION FUNCTION4 Maximum SYNC Clock Rate TBD 250 MHz SYNC_CLK Alignment Resolution5 ±1 SYSCLK Cycles 1 To achieve the best possible phase noise, the largest amplitude clock possible should be used. Reducing the clock input amplitude will reduce the phase noise per- formance of the device. 2 Wake-up time refers to the recovery from analog power-down modes (see section on Power-Down Modes of Operation). The longest time required is for the reference clock multiplier PLL to relock to the reference. The wake-up time assumes there is no capacitor on DAC_BP and that the recommended PLL loop filter values are used. 3 SYSCLK cycle refers to the actual clock frequency used on-chip by the DDS. If the reference clock multiplier is used to multiply the external reference clock frequency, the SYSCLK frequency is the external frequency multiplied by the reference clock multiplication factor. If the reference clock multiplier is not used, the SYSCLK fre- quency is the same as the external reference clock frequency. 4 SYNC_CLK = ¼ SYSCLK rate. For SYNC_CLK rates ≥ 50 MHz, the high speed sync enable bit, CFR2<11>, should be set. 5 This parameter indicates that the digital synchronization feature cannot overcome phase delays (timing skew) between system clock rising edges. If the system clock edges are aligned, the synchronization function should not increase the skew between the two edges. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |