WM8985 datasheet(86/118 Pages) WOLFSON

86 / 118 page

WM8985

Pre-Production

PP, Rev 3.4, October 2006

2-WIRE SERIAL CONTROL MODE

The WM8985 supports software control via a 2-wire serial bus. Many devices can be controlled by

the same bus, and each device has a unique 7-bit device address (this is not the same as the 7-bit

address of each register in the WM8985).

The WM8985 operates as a slave device only. The controller indicates the start of data transfer with

a high to low transition on SDIN while SCLK remains high. This indicates that a device address and

data will follow. All devices on the 2-wire bus respond to the start condition and shift in the next eight

bits on SDIN (7-bit address + Read/Write bit, MSB first). If the device address received matches the

address of the WM8985, the WM8985 responds by pulling SDIN low on the next clock pulse (ACK).

If the address is not recognised or the R/W bit is ‘1’ when operating in write only mode, the WM8985

returns to the idle condition and waits for a new start condition and valid address.

During a write, once the WM8985 has acknowledged a correct address, the controller sends the first

byte of control data (B15 to B8, i.e. the WM8985 register address plus the first bit of register data).

The WM8985 then acknowledges the first data byte by driving SDIN low for one clock cycle. The

controller then sends the second byte of control data (B7 to B0, i.e. the remaining 8 bits of register

data), and the WM8985 acknowledges again by pulling SDIN low.

Transfer is complete when there is a low to high transition on SDIN while SCLK is high. After a

complete sequence the WM8985 returns to the idle state and waits for another start condition. If a

start or stop condition is detected out of sequence at any point during data transfer (i.e. SDIN

changes while SCLK is high), the control interface returns to the idle condition.

SDIN

SCLK

1st register data bit

DEVICE ADDRESS

(7 BITS)

RD / WR

BIT

ACK

(LOW)

CONTROL BYTE 1

(BITS 15 TO 8)

CONTROL BYTE 1

(BITS 7 TO 0)

remaining 8 bits of

STOP

START

ACK

(LOW)

ACK

(LOW)

Figure 39 2-Wire Serial Control Interface

In 2-wire mode the WM8985 has a fixed device address, 0011010.

RESETTING THE CHIP

The WM8985 can be reset by performing a write of any value to the software reset register (address

0h). This will cause all register values to be reset to their default values. In addition to this there is a

Power-On Reset (POR) circuit which ensures that the registers are initially set to default when the

device is powered up.

POWER SUPPLIES

The WM8985 requires four separate power supplies:

AVDD1 and AGND1: Analogue supply, powers all internal analogue functions and output drivers

LOUT1, ROUT1, OUT3 and OUT4. AVDD1 must be between 2.5V and 3.6V and has the most

significant impact on overall power consumption (except for power consumed in the headphones).

Higher AVDD1 will improve audio quality.

AVDD2 and AGND2: Output driver supplies, power LOUT2 and ROUT2. AVDD2 must be between

2.5V and 3.6V. AVDD2 can be tied to AVDD1, but it requires separate layout and decoupling

capacitors to curb harmonic distortion.

DCVDD: Digital core supply, powers all digital functions except the audio and control interface pads.

DCVDD must be between 1.71V and 3.6V, and has no effect on audio quality. The return path for

DCVDD is DGND, which is shared with DBVDD.

DBVDD must be between 1.71V and 3.6V. DBVDD return path is through DGND.

It is possible to use the same supply voltage for all four supplies. However, digital and analogue

supplies should be routed and decoupled separately on the PCB to keep digital switching noise out

of the analogue signal paths.

WM8985 Datasheet(PDF) 86 Page - Wolfson Microelectronics plc

WM8985 Datasheet(HTML) 86 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL