| Electronic Components Datasheet Search |
|
MAX9985 Datasheet(PDF) 13 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX9985 Datasheet(HTML) 13 Page - Maxim Integrated Products |
|
13 / 15 page ![]() Dual, SiGe, High-Linearity, 700MHz to 1000MHz Downconversion Mixer with LO Buffer/Switch ______________________________________________________________________________________ 13 LO Buffer Bias Resistors Bias currents for the two on-chip LO buffers is opti- mized by fine-tuning the off-chip resistors on LODBIAS (pin 17) and LOMBIAS (pin 29). The current in the buffer amplifiers is reduced by increasing the value of these resistors, but performance may degrade. See the Typical Operating Characteristics for key performance parameters versus this resistor value. Doubling the value of these resistors reduces the total chip current by approximately 50mA (see Table 1). IF Amplifier Bias Resistors Bias currents for the two on-chip IF amplifiers are opti- mized by fine-tuning the off-chip resistors on IFDBIAS (pin 11) and IFMBIAS (pin 35). The current in the IF amplifiers is decreased by raising the value of these resistors, but performance may degrade. See the Typical Operating Characteristics for key performance parameters versus this resistor value. Doubling the value of this resistor reduces the current in each IF amplifier from 100mA to approximately 50mA (see Table 1). LEXT Inductor Short LEXT_ to ground using a 0Ω resistor. For applica- tions requiring improved RF-to-IF and LO-to-IF isolation, LEXT_ can be used by connecting a low-ESR inductor from LEXT_ to GND. See the Typical Operating Characteristics on RF-to-IF port isolation and LO-to-IF port leakage for various inductor values. The load impedance presented to the mixer must be such that any capacitance from both IF- and IF+ to ground do not exceed several picofarads to ensure stable operating conditions. Approximately 100mA flows through LEXT_, so it is important to use a low-DCR wire-wound inductor. Layout Considerations A properly designed PCB is an essential part of any RF/microwave circuit. Keep RF signal lines as short as possible to reduce losses, radiation, and inductance. For the best performance, route the ground pin traces directly to the exposed paddle under the package. The PCB exposed paddle MUST be connected to the ground plane of the PCB. It is suggested that multiple vias be used to connect this paddle to the lower-level ground planes. This method provides a good RF/ther- mal-conduction path for the device. Solder the exposed paddle on the bottom of the device package to the PCB. Refer to the MAX9985 Evaluation Kit as a refer- ence for board layout. Gerber files are available upon request at www.maxim-ic.com. Power-Supply Bypassing Proper voltage-supply bypassing is essential for high- frequency circuit stability. Bypass each VCC pin and TAPMAIN/TAPDIV with the capacitors shown in the Typical Application Circuit (see Table 2 for component values). Place the TAPMAIN/TAPDIV bypass capacitor to ground within 100 mils of the pin. Exposed Paddle RF/Thermal Considerations The exposed paddle (EP) of the MAX9985’s 36-pin thin QFN-EP package provides a low thermal-resistance path to the die. It is important that the PCB on which the MAX9985 is mounted be designed to conduct heat from the EP. In addition, provide the EP with a low- inductance path to electrical ground. The EP MUST be soldered to a ground plane on the PCB, either directly or through an array of plated via holes. Table 2. Component Values COMPONENT VALUE DESCRIPTION C1, C2, C7, C8 39pF Microwave capacitors (0402) C3, C6 0.033µF Microwave capacitors (0603) C4, C5 — Not used C9, C13, C15, C17, C18 0.01µF Microwave capacitors (0402) C10, C11, C12, C19, C20, C21 150pF Microwave capacitors (0603) C14, C16 82pF Microwave capacitors (0402) L1, L2, L4, L5 560nH Wire-wound high-Q inductors (0805) L3, L6 30nH Wire-wound high-Q inductors (0603) R1, R4 1.07kΩ ±1% resistors (0402) R2, R5 1.1kΩ ±1% resistors (0402) R3, R6 0Ω Resistors (1206) T1, T2 4:1 Transformers (200:50) Mini-Circuits TC4-1W-7A U1 — MAX9985 IC |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |