PCM1608 datasheet(18/46 Pages) TI2

18 / 46 page

www.ti.com

SERIAL CONTROL INTERFACE

R0001-02

IDX6

MSB

LSB

IDX5

IDX4

R/W

IDX3

IDX2

IDX1

IDX0

Read/Write Operation

0 = Write Operation

1 = Read Operation (Register Index is Ignored)

IDX0

R/W

MDI

R/W IDX6

IDX1

IDX2

IDX3

IDX4

IDX5

IDX6

T0048-02

SINGLE REGISTER READ OPERATION

PCM1608

SBAS164B – DECEMBER 2000 – REVISED JULY 2005

The serial control interface is a 4-wire synchronous serial port that operates asynchronously to the serial audio

interface. The serial control interface is used to program and read the on-chip mode registers. The control

interface includes MDO (pin 33), MDI (pin 34), MC (pin 35), and ML (pin 36). MDO is the serial data output, used

to read back the values of the mode registers; MDI is the serial data input, used to program the mode registers;

MC is the serial bit clock, used to shift data in and out of the control port; and ML is the control port latch clock.

All write operations for the serial control port use 16-bit data words. Figure 24 shows the control data word

format. The most significant bit is the read/write (R/W) bit. When set to 0, this bit indicates a write operation.

Seven bits, labeled IDX[6:0], set the register index (or address) for the write operation. The least significant eight

bits, D[7:0], contain the data to be written to the register specified by IDX[6:0].

Figure 25 shows the functional timing diagram for writing to the serial control port. ML is held at a logic-1 state

until a register is to be written. To start the register write cycle, ML is set to logic-0. Sixteen clocks are then

provided on MC, corresponding to the 16 bits of the control data word on MDI. After the sixteenth clock cycle has

completed, ML is set to logic-1 to latch the data into the indexed mode control register.

Figure 24. Control Data Word Format for MDI

Figure 25. Write Operation Timing

Read operations use the 16-bit control word format shown in Figure 24. For read operations, the R/W bit is set

to 1. Read operations ignore the index bits, IDX[6:0], of the control data word. Instead, the REG[6:0] bits in

control register 11 are used to set the index of the register that is to be read during the read operation. Bits

IDX[6:0] should be set to 00h for read operations.

The details of the read operation are shown in Figure 26. First, control register 11 must be written with the index

of the register to be read back. Additionally, the INC bit must be set to logic-0 in order to disable the

auto-increment read function. The read cycle is then initiated by setting ML to logic-0 and setting the R/W bit of

the control data word to logic-1, indicating a read operation. MDO remains in a high-impedance state until the

last eight bits of the 16-bit read cycle, which correspond to the eight data bits of the register indexed by the

REG[6:0] bits of control register 11. The read cycle is completed when ML is set to 1, immediately after the MC

clock cycle for the least-significant bit of the indexed control register has completed.

PCM1608 Datasheet(PDF) 18 Page - Texas Instruments

PCM1608 Datasheet(HTML) 18 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

Datasheet Download

Link URL