CDC582

3.3-V PHASE-LOCK LOOP CLOCK DRIVER

WITH DIFFERENTIAL LVPECL CLOCK INPUTS

SCAS446B – JULY 1994 – REVISED FEBRUARY 1996

5

POST OFFICE BOX 655303

Terminal Functions

TERMINAL

I/O

DESCRIPTION

NAME

NO.

I/O

DESCRIPTION

CLKIN

CLKIN

44, 45

I

Clock input. CLKIN and CLKIN are the differential clock signals to be distributed by the CDC582 clock-driver

circuit. These inputs are used to provide the reference signal to the integrated PLL that generates the clock

output signals. CLKIN and CLKIN must have a fixed frequency and fixed phase for the PLL to obtain phase

lock. Once the circuit is powered up and valid CLKIN and CLKIN signals are applied, a stabilization time is

required for the PLL to phase lock the feedback signal to its reference signal.

CLR

40

I

Clear. CLR is used to reset the VCO/4 reference frequency. CLR is negative-edge triggered and should be

strapped to VCC or GND for normal operation.

FBIN

48

I

Feedback input. FBIN provides the feedback signal to the internal PLL. FBIN must be hardwired to one of

the twelve clock outputs to provide frequency and phase lock. The internal PLL adjusts the output clocks

to obtain zero phase delay between the FBIN and the differential clock input (CLKIN and CLKIN).

OE

42

I

Output enable. OE is the output enable for all outputs. When OE is low, all outputs are enabled. When OE

is high, all outputs are driven to the low state. Since the feedback signal for the PLL is taken directly from

an output terminal, placing the outputs in the logic low state interrupts the feedback loop; therefore, when

a high-to-low transition occurs at OE, enabling the output buffers, a stabilization time is required before the

PLL obtains phase lock.

SEL1, SEL0

51, 50

I

Output configuration select.

SEL0 and SEL1 select the output configuration for each output bank

(e.g., 1

, 1/2

, or 2

) (see Tables 1 and 2).

TEST

41

I

TEST is used to bypass the PLL circuitry for factory testing of the device. When TEST is low, all outputs

operate using the PLL circuitry. When TEST is high, the outputs are placed in a test mode that bypasses

the PLL circuitry. TEST should be strapped to GND for normal operation.

1Y1 – 1Y3

2Y1 – 2Y3

3Y1 – 3Y3

2, 5, 8

12, 15, 18

22, 25, 28

O

These outputs are configured by SEL1 and SEL0 to transmit one-half or one-fourth the frequency of the

VCO. The relationship between the input clock frequency and the output frequency is dependent on SEL1

and SEL0 and the frequency of the output being fed back to FBIN. The duty cycle of the Y outputs is

nominally 50% independent of the duty cycle of the input clock signals.

4Y1 – 4Y3

32, 35, 38

O

These outputs transmit one-half the frequency of the VCO. The relationship between the input clock

frequency and the output frequency is dependent on the frequency of the output being fed back to FBIN.

The duty cycle of the Y outputs is nominally 50% independent of the duty cycle of CLKIN.

– 0.5 V to 4.6 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 0.5 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 0.5 V to 5.5 V

. . .

64 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 20 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 50 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES:

1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.

2. The maximum package power dissipation is calculated using a junction temperature of 150

°C and a board trace length of 750 mils.

For more information, refer to the

Package Thermal Considerations application note in the ABT Advanced BiCMOS Technology Data

Book, literature number SCBD002.