ATmega88 datasheet(175/340 Pages) ATMEL

175 / 340 page

175

7530H–AVR–02/09

ATmega48/88/168 Automotive

17.5.3

Transmitter Flags and Interrupts

The USART Transmitter has two flags that indicate its state: USART Data Register Empty

(UDREn) and Transmit Complete (TXCn). Both flags can be used for generating interrupts.

The Data Register Empty (UDREn) Flag indicates whether the transmit buffer is ready to receive

new data. This bit is set when the transmit buffer is empty, and cleared when the transmit buffer

contains data to be transmitted that has not yet been moved into the Shift Register. For compat-

ibility with future devices, always write this bit to zero when writing the UCSRnA Register.

When the Data Register Empty Interrupt Enable (UDRIEn) bit in UCSRnB is written to one, the

USART Data Register Empty Interrupt will be executed as long as UDREn is set (provided that

global interrupts are enabled). UDREn is cleared by writing UDRn. When interrupt-driven data

transmission is used, the Data Register Empty interrupt routine must either write new data to

UDRn in order to clear UDREn or disable the Data Register Empty interrupt, otherwise a new

interrupt will occur once the interrupt routine terminates.

The Transmit Complete (TXCn) Flag bit is set one when the entire frame in the Transmit Shift

The TXCn Flag bit is automatically cleared when a transmit complete interrupt is executed, or it

can be cleared by writing a one to its bit location. The TXCn Flag is useful in half-duplex commu-

nication interfaces (like the RS-485 standard), where a transmitting application must enter

receive mode and free the communication bus immediately after completing the transmission.

When the Transmit Compete Interrupt Enable (TXCIEn) bit in UCSRnB is set, the USART

Transmit Complete Interrupt will be executed when the TXCn Flag becomes set (provided that

global interrupts are enabled). When the transmit complete interrupt is used, the interrupt han-

dling routine does not have to clear the TXCn Flag, this is done automatically when the interrupt

is executed.

17.5.4

Parity Generator

The Parity Generator calculates the parity bit for the serial frame data. When parity bit is enabled

(UPMn1 = 1), the transmitter control logic inserts the parity bit between the last data bit and the

first stop bit of the frame that is sent.

17.5.5

Disabling the Transmitter

The disabling of the Transmitter (setting the TXEN to zero) will not become effective until ongo-

ing and pending transmissions are completed, i.e., when the Transmit Shift Register and

Transmit Buffer Register do not contain data to be transmitted. When disabled, the Transmitter

will no longer override the TxDn pin.

17.6

Data Reception – The USART Receiver

The USART Receiver is enabled by writing the Receive Enable (RXENn) bit in the

UCSRnB Register to one. When the Receiver is enabled, the normal pin operation of the RxDn

pin is overridden by the USART and given the function as the Receiver’s serial input. The baud

rate, mode of operation and frame format must be set up once before any serial reception can

be done. If synchronous operation is used, the clock on the XCKn pin will be used as transfer

clock.

ATmega88 Datasheet(PDF) 175 Page - ATMEL Corporation

ATmega88 Datasheet(HTML) 175 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL