WM8311 datasheet(62/302 Pages) WOLFSON

62 / 302 page

WM8311

Pre-Production

PP, May 2012, Rev 3.1

Note that Page 0 and Page 1 will be programmed during manufacture, and cannot be re-written. OTP

Write is then only possible to Page 2 and Page 3. Selecting the OTP_BULK bit will select OTP Write

to Page 2 and Page 3 only.

Note that selecting the OTP_BULK option will cause an OTP Error to be indicated (see Section 14.5).

This is because the Bulk Write to Page 0 and Page 1 is not permitted after the factory configuration of

the WM8311. It is still possible to Verify the OTP Bulk Write, but the OTP_ERR_EINT flag must be

cleared before doing so. The recommended procedure is to Write Page 2 and Page 3 using single

page OTP Write commands.

All other bits in the OTP Control Register should be set to 0 when a Write command is issued. (Note

that OTP_PROG should be set to 0 when a Write command is issued.)

The programming supply voltage PROGVDD is required for the OTP Write command. It is also

necessary to overdrive the LDO12VOUT pin from an external supply. See Section 6 for details of the

required supply voltages.

For typical applications, it is recommended to Write Page 2 and Page 3 in two separate commands.

The OTP Control Register contents for these OTP Write Commands are detailed in Table 24.

WRITE COMMAND

OTP CONTROL REGISTER VALUE

OTP Write Page 2

2202h

OTP Write Page 3

2203h

Table 24 OTP Write Command

14.4.4 OTP VERIFY COMMAND

The Verify command compares one or all data pages of the OTP with data in the corresponding

page(s) of the DCRW. The Verify commands are selected by writing 1 to the OTP_VERIFY bit.

The OTP memory is selected by setting the OTP_MEM bit to 1. (Note that the WM8311 does not

support verifying the external ICE memory.)

The Read Margin Level is selected by setting the OTP_READ_LVL. The recommended setting for the

OTP Verify command is Margin 1. The OTP_READ_LVL field should be set to 10b.

To verify a single memory page, the applicable page is selected by setting the OTP_PAGE field. To

verify all memory pages, the OTP_BULK bit should be set to 1.

All other bits in the OTP Control Register should be set to 0 when a Verify command is issued. (Note

that OTP_PROG should be set to 0 when a Verify command is issued.)

If the OTP Verify operation is unsuccessful (ie. the WM8311 detects a difference between the

selected pages of the OTP and DCRW memories), then this is indicated by the OTP_ERR_EINT

Interrupt flag, as described in Section 14.5.

Note that, when Verifying the OTP after it has been Finalised, the CUST_OTP_FINAL bit needs to be

set in the DCRW using a register write to R30736 prior to the OTP_VERIFY operation. This is

because the OTP_FINAL command does not set the CUST_OTP_FINAL bit in the DCRW; it only sets

it in the OTP memory. If the CUST_OTP_FINAL bit is not set in DCRW, then the OTP_VERIFY

command will result in an OTP error indication.

The OTP Control Register contents for all OTP Verify Commands are detailed in Table 25.

VERIFY COMMAND

OTP CONTROL REGISTER VALUE

OTP Verify Page 0

2480h

OTP Verify Page 1

2481h

OTP Verify Page 2

2482h

OTP Verify Page 3

2483h

OTP Verify All

24A0h

Table 25 OTP Verify Command (Margin 1)

WM8311 Datasheet(PDF) 62 Page - Wolfson Microelectronics plc

WM8311 Datasheet(HTML) 62 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL