WM8311 datasheet(63/302 Pages) WOLFSON

63 / 302 page

Pre-Production

WM8311

PP, May 2012, Rev 3.1

14.4.5 OTP FINALISE COMMAND

The Finalise command sets the OTP finalise bit for the user-programmable pages of the OTP

memory. The Finalise commands are selected by writing 1 to the OTP_FINAL bit.

Note that Page 0 and Page 1 will be programmed and finalised during manufacture; these memory

pages cannot be re-written by users. Following the user Finalise command, Page 2 and Page 3 of the

OTP memory will be prevented from any further OTP Write commands. Each page of the OTP

memory can be programmed only once; the OTP Finalise command ensures that any subsequent

Write commands will have no effect and that the OTP contents are maintained securely.

The OTP memory is selected by setting the OTP_MEM bit to 1. (Note that the WM8311 does not

support this function on the external ICE memory.)

The Customer Finalise bit (CUST_OTP_FINAL) is in Page 2. This page is selected by setting

OTP_PAGE = 10. Note that the Page 2 finalise bit locks the contents of Page 2 and Page 3.

All other bits in the OTP Control Register should be set to 0 when a Finalise command is issued.

(Note that OTP_PROG should be set to 0 when a Finalise command is issued.)

The programming supply voltage PROGVDD is required for the OTP Finalise command. It is also

necessary to overdrive the LDO12VOUT pin from an external supply. See Section 6 for details of the

required supply voltages.

Note that the OTP_FINAL command does not set the CUST_OTP_FINAL bit in the DCRW; it only

sets it in the OTP memory. Care is required when verifying a Finalised OTP page, to avoid an OTP

error indication, as described in Section 14.4.4.

The OTP Control Register contents for the OTP Finalise Command is detailed in Table 26. This is the

only recommended OTP Finalise Command; no variants of the Finalise Command should be used.

FINALISE COMMAND

OTP CONTROL REGISTER VALUE

OTP Finalise Page 2

(Note that this command finalises

the contents of OTP Page 2 and

Page 3.)

2802h

Table 26 OTP Finalise Command

14.4.6 OTP CONTROL REGISTER

The OTP Control register (R16394) is defined in Table 27. Note that some of the OTP Programming

registers are locked by the WM8311 User Key. These registers can only be changed by writing the

appropriate code to the Security register, as described in Section 12.4.

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

R16394 (400Ah)

OTP Control

OTP_PROG

Selects the PROGRAM device state.

0 = No action

1 = Select PROGRAM mode

Note that, after PROGRAM mode has

been selected, the chip will remain in

PROGRAM mode until a Device Reset.

Protected by user key

OTP_MEM

Selects ICE or OTP memory for Program

commands.

0 = ICE

1 = OTP

Protected by user key

OTP_FINAL

Selects the FINALISE command,

preventing further OTP programming.

0 = No action

1 = Finalise Command

Protected by user key

OTP_VERIFY

Selects the VERIFY command for the

selected OTP memory page(s).

WM8311 Datasheet(PDF) 63 Page - Wolfson Microelectronics plc

WM8311 Datasheet(HTML) 63 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL