| Electronic Components Datasheet Search |
|
RT8060A Datasheet(PDF) 7 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT8060A Datasheet(HTML) 7 Page - Richtek Technology Corporation |
|
7 / 10 page ![]() RT8060A 7 DS8060A-00 March 2011 www.richtek.com Applications Information The basic RT8060A application circuit is shown in Typical Application Circuit. External component selection is determined by the maximum load current and begins with the selection of the inductor value and operating frequency followed by CIN and COUT. Inductor Selection For a given input and output voltage, the inductor value and operating frequency determine the ripple current. The ripple current ΔIL increases with higher VIN and decreases with higher inductance. OUT OUT L(MAX) IN(MAX) VV L x 1 fI V ⎡⎤ ⎡⎤ =− ⎢⎥ ⎢⎥ ×Δ ⎣⎦ ⎢⎥ ⎣⎦ A smaller inductor changes its current more quickly for a given voltage drive than a larger inductor, resulting in faster transient response. A larger inductor will reduce output ripple and current ripple, but at the expense of reduced transient performance and a physically larger inductor package size. For this reason, a larger capacitor, C1, will be required for larger inductor sizes. The input regulator has an instantaneous peak current clamp to prevent the inductor from saturating during transient load or start-up conditions. The clamp is designed so that it does not interfere with normal operation at high loads and reasonable inductor ripple. It is intended to prevent inductor current runaway in case of a shorted output. The DC winding resistance and AC core losses of the inductor will also affect efficiency, and therefore available output power. These effects are difficult to characterize and vary by application. Some inductors and capacitors that may be suitable for this application are listed in Table below : Length Width Height Inductance RDC IDC (mm) (mm) (mm) ( μH) (m Ω) (A) P/N Max. Max. Max. L Max. Max. Supplier VLF5012ST-1R0N2R5 5 4.8 1.2 1 50 3.3 VLF5014ST-2R2M2R3 5 4.8 1.4 2.2 73 3 VLF3010A-1 3 2.8 1 2.2 120 1 VLF3012A 3 2.8 1.2 2.2 100 1 VLS2010E 2.1 2.1 1 2.2 228 1 VLS2012E 2.1 2.1 1.2 2.2 153 1 TDK NR6045T1R0N 6 6 4.5 1 19 4.2 CB2016T2R2M 2.2 1.8 1.8 2.2 130 1 NR6020T2R2N 6 6 2 2.2 34 2.7 NR3015 3 3 1.5 2.2 60 1.48 TAIYO LPS4018 3.9 3.9 1.7 3.3 80 2.2 CoilCraft D53LC 5 5 3 3.3 34 2.26 DB318C 3.8 3.8 1.8 3.3 70 1.55 Toko WE-TPC Type M1 4.8 4.8 1.8 3.3 65 1.95 Wurth OUT OUT L IN VV ΔI x 1 fL V ⎡⎤ ⎡⎤ =− ⎢⎥ ⎢⎥ × ⎣⎦ ⎣⎦ Having a lower ripple current reduces the ESR losses in the output capacitors and the output voltage ripple. Highest efficiency operation is achieved at low frequency with small ripple current. This, however, requires a large inductor. A reasonable starting point for selecting the ripple current is ΔIL = 0.4(IMAX). The largest ripple current occurs at the highest VIN. To guarantee that the ripple current stays below a specified maximum, the inductor value should be chosen according to the following equation : Table |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |