LM4780 datasheet(19/24 Pages) NSC

19 / 24 page

Application Information (Continued)

20058698

The load current I

L will be much larger than input bias current

I, thus V1 will follow the output voltage directly, i.e. in phase.

Therefore the voltage appearing at the non-inverting input is

effectively positive feedback and the circuit may oscillate. If

there was only one device to worry about then the values of

1 and R2 would probably be small enough to be ignored;

however, several devices normally comprise a total system.

Any ground return of a separate device, whose output is in

phase, can feedback in a similar manner and cause insta-

bilities. Out of phase ground loops also are troublesome,

causing unexpected gain and phase errors.

The solution to most ground loop problems is to always use

a single-point ground system, although this is sometimes

impractical. The third figure above is an example of a single-

point ground system.

The single-point ground concept should be applied rigor-

ously to all components and all circuits when possible. Vio-

lations of single-point grounding are most common among

printed circuit board designs, since the circuit is surrounded

by large ground areas which invite the temptation to run a

device to the closest ground spot. As a final rule, make all

ground returns low resistance and low inductance by using

large wire and wide traces.

Occasionally, current in the output leads (which function as

antennas) can be coupled through the air to the amplifier

input, resulting in high-frequency oscillation. This normally

happens when the source impedance is high or the input

leads are long. The problem can be eliminated by placing a

small capacitor, C

C, (on the order of 50pF to 500pF) across

the LM4780 input terminals. Refer to the External Compo-

nents Description section relating to component interaction

with C

REACTIVE LOADING

It is hard for most power amplifiers to drive highly capacitive

loads very effectively and normally results in oscillations or

ringing on the square wave response. If the output of the

LM4780 is connected directly to a capacitor with no series

resistance, the square wave response will exhibit ringing if

the capacitance is greater than about 0.2µF. If highly capaci-

tive loads are expected due to long speaker cables, a

method commonly employed to protect amplifiers from low

impedances at high frequencies is to couple to the load

through a 10

Ω resistor in parallel with a 0.7µH inductor. The

inductor-resistor combination as shown in the Figure 5 iso-

lates the feedback amplifier from the load by providing high

output impedance at high frequencies thus allowing the 10

Ω

resistor to decouple the capacitive load and reduce the Q of

the series resonant circuit. The LR combination also pro-

vides low output impedance at low frequencies thus shorting

out the 10

Ω resistor and allowing the amplifier to drive the

series RC load (large capacitive load due to long speaker

cables) directly.

INVERTING AMPLIFIER APPLICATION

The inverting amplifier configuration may be used instead of

the more common non-inverting amplifier configuration

shown in Figure 1. The inverting amplifier can have better

THD+N performance and eliminates the need for a large

capacitor (Ci) reducing cost and space requirements. The

values show in Figure 6 are only one example of an amplifier

with a gain of 20V/V (Gain = -R

f/Ri). For different resistor

values, the value of R

B should be eqaul to the parallel

combination of R

f and Ri.

If the DC blocking input capacitor (C

IN) is used as shown, the

lower -3dB point is found using Equation (8) as discussed in

the Proper Selection of External Components section.

LM4780 Datasheet(PDF) 19 Page - National Semiconductor (TI)

LM4780 Datasheet(HTML) 19 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL