MICRF501 datasheet(9/18 Pages) MICREL

9 / 18 page

March 2003

MICRF501

Micrel

Applications Information

VCO and PLL Section

The frequency synthesizer consists of a VCO, crystal oscilla-

tor, dual-modulus prescaler, programmable frequency divid-

ers, phase-detector, charge pump, lock detector and an

external loop filter. The dual-modulus prescaler divides the

VCO-frequency by 32/33. This mode is controlled by the A-

divider. There are two sets of M, N and A-frequency dividers.

Using both sets in transmit mode, FSK can be implemented

by switching between those two sets. The phase-detector is

a frequency/phase detector with back slash pulses to mini-

mize phase noise. The VCO, crystal oscillator, charge pump,

lock detector and the loop filter will be described in detail

below.

Voltage Controlled Oscillator (VCO)

VDD

Pin 5

Pin 6

C13

MA4ST350

C35

2.2p

3.6k

15p

47nH

47k

loopfilter_output

Pin 7

OSCOUT

Figure 3. VCO

The circuit schematic of the VCO with external components

is shown in Figure 3. The VCO is basically a Colpitts oscilla-

tor. The oscillator has an external resonator and varactor.

The resonator consists of inductor L1 and the series connec-

tion of capacitor C13, the internal capacitance, the capaci-

tance of the varactor and C35 in parallel with D1. The

capacitance of the varactor (D1) decreases as the input

voltage increases. The VCO frequency will therefore in-

crease as the input voltage increases. The VCO has a

positive gain (MHz/Volt). C35 is added, if necessary, to bring

VCO tuning voltage to its middle range or VCC/2, which is

measured at Pin 9 - CMPOUT.

If the value of capacitor C13 and C14 become too small the

amplitude of the VCO signal decreases, which leads to lower

output power.

The layout of the VCO is very critical. The external compo-

nents should be placed as close to the input pin (Pin 6) as

possible. The anode of the varactor D1 must be placed next

to pins 7 and 8. Ground vias should be next to component

pads.

Crystal Oscillator

The crystal oscillator is the reference for the RF output

frequency as well as for the LO frequency in the receiver. The

crystal oscillator is a very critical block since very good phase

and frequency stability is required. The schematic of the

crystal oscillator with external components for 10MHz is

shown in Figure 4. These components are optimized for a

crystal with 15pF load capacitance.

DIFVDD

C21

47p

C20

2-6p

C36

10MHz

C22

5.6p

Pin 12

Pin 13

XOSCOUT

DIGGND

Figure 4. Crystal Oscillator

The crystal oscillator is tuned by varying the trimming capaci-

tor C20. The drift of the RF frequency is the same as the drift

of crystal frequency when measured in ppm. The total differ-

ence in ppm,

∆f(ppm), between the tuned RF frequency and

the drifted frequency is given by:

∆f(ppm) = S

T × ∆T + n × ∆t

where:

•

T is the total temperature coefficient of the oscillator

frequency (due to crystal and components) in ppm

°C.

•

∆T is the change in temperature from room

temperature, at which the crystal was tuned.

•

n is the ageing in ppm/year.

•

∆t is the time (in years) elapsed since the transceiver

was last tuned.

The demodulator will not be able to decode data when

∆f(Hz) = ∆f(ppm) × f

RF is larger than the FSK frequency

deviation. For small frequency deviations, the crystal should

be pre-aged, and should have a small temperature coeffi-

cient. The circuit has been tested with a 10MHz crystal, but

other crystal frequencies can be used as well.

The circuit has been tested with a 10MHz crystal, but other

crystal frequencies can be used as well.

Prestart of XCO

The start-up time of a crystal oscillator is typically some

milliseconds. Therefore, to save current consumption, the

MICRF501 circuit has been designed so that the XCO is

turned on before any other circuit block. During start-up the

XCO amplitude will eventually reach a sufficient level to

trigger the M-counter. After counting two M-counter output

pulses the rest of the circuit will be turned on. The current

consumption during the prestart period is approximately

300

µA.

Lock Detector

The MICRF501 circuit has a lock detector feature that indi-

cates whether the PLL is in lock or not. A logic high on Pin 15

(LOCKDET) means that the PLL is in lock.

The phase detector output is converted into a voltage that is

filtered by the external capacitor C23, connected to Pin 14,

LDC. The resulting DC voltage is compared to a reference

window set by bits Ref0 – Ref5. The reference window can be

stepped up/down linearly between 0V, Ref0 – Ref5 =1, and

Ref0 – Ref5 = 0, which gives the highest value (DC voltage)

of the reference window. The size of the window can either be

MICRF501 Datasheet(PDF) 9 Page - Micrel Semiconductor

MICRF501 Datasheet(HTML) 9 Page - Micrel Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Datasheet Download

Link URL