| Electronic Components Datasheet Search |
|
LTC1844 Datasheet(PDF) 7 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC1844 Datasheet(HTML) 7 Page - Linear Technology |
|
7 / 12 page ![]() 7 LTC1844 Series 1844ia APPLICATIO S I FOR ATIO output current change of 1mA to 100mA is – 4mV typical at VOUT = 1.25V. At VOUT = 5V, load regulation is: (5V/1.25V)(– 4mV) = –16mV Because the ADJ pin is relatively high impedance (depend- ing on the resistor divider used), stray capacitance at this pin can introduce significant phase shift in the error amplifier loop. The PCB layout should be designed to absolutely minimize the capacitance seen at the ADJ pin. To ensure stability over all operating conditions when utilizing large divider resistors, it may be necessary to use a small ceramic feedforward capacitor (~1000pF) in par- allel with the upper divider resistor (see CFF in Figure 2). As an added bonus, this capacitor will improve transient response. Bypass Capacitance and Low Noise Performance A bypass capacitor can optionally be connected from the BYP pin to ground to lower output voltage noise. A good quality low leakage capacitor is recommended. This ca- pacitor will bypass the input of the error amplifier, provid- ing a low frequency noise pole. The noise pole provided by this bypass capacitor will lower the output voltage noise to as low as 30 µVRMS with the addition of a 0.1µF capacitor. Initial regulator power-up time is inversely proportional to the size of the bypass capacitor, slowing to 10ms with a 0.1 µF capacitor and 10µF output capacitor. However, the LTC1844 does not discharge the bypass capacitor when put into shutdown and thus the shutdown exit delay can be much shorter ( ≈70µs) than initial power-up time if the shutdown duration is brief (<10ms). The maximum shut- down duration required to allow fast shutdown exit is determined by the capacitor leakage current, thus a low leakage bypass capacitor is recommended. Output Capacitance and Transient Response The LTC1844 regulators are designed to be stable with a wide range of output capacitors. The ESR of the output capacitor affects stability, most notably with small capaci- tors. A minimum output capacitor of 1 µF with an ESR of 0.3 Ω or less is recommended to ensure stability. The LTC1844 is a micropower device and output transient response will be a function of output capacitance. Larger values of output capacitance decrease the peak deviations and provide improved transient response for larger load current changes. Note that bypass capacitors used to decouple individual components powered by the LTC1844 will increase the effective output capacitor value. The shaded region of Figure 3 defines the region over which the LTC1844 regulators are stable. The maximum ESR allowed is 0.3 Ω. High ESR tantalum and electrolytic ca- pacitors may be used, but a low ESR ceramic capacitor must be in parallel at the output. There is no minimum ESR requirement. Extra consideration must be given to the use of ceramic capacitors. Ceramic capacitors are manufactured with a variety of dielectrics, each with different behavior across Figure 3. Stability OUTPUT CAPACITANCE ( µF) 0.33 1 3.3 10 33 0.20 0.25 STABLE REGION 0.30 100 1844 F03 0.15 0.10 0 0.05 0.40 0.35 |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |