CC1100-RTR1 datasheet(73/100 Pages) TI1

73 / 100 page

CC1100

SWRS038D

Page 73 of 92

0x16: MCSM2 – Main Radio Control State Machine Configuration

Bit

Field Name

Reset

R/W

Description

7:5

Reserved

RX_TIME_RSSI

R/W

Direct RX termination based on RSSI measurement (carrier sense). For

ASK/OOK modulation, RX times out if there is no carrier sense in the first 8

symbol periods.

RX_TIME_QUAL

R/W

When the RX_TIME timer expires, the chip checks if sync word is found

when RX_TIME_QUAL=0, or either sync word is found or PQI is set when

RX_TIME_QUAL=1.

RX_TIME[2:0]

7 (111)

R/W

Timeout for sync word search in RX for both WOR mode and normal RX

operation. The timeout is relative to the programmed EVENT0 timeout.

2:0

The RX timeout in µs is given by EVENT0·C(RX_TIME, WOR_RES) ·26/X, where C is given by the table below and X is

the crystal oscillator frequency in MHz:

Setting

WOR_RES = 0

WOR_RES = 1

WOR_RES = 2

WOR_RES = 3

0 (000)

3.6058

18.0288

32.4519

46.8750

1 (001)

1.8029

9.0144

16.2260

23.4375

2 (010)

0.9014

4.5072

8.1130

11.7188

3 (011)

0.4507

2.2536

4.0565

5.8594

4 (100)

0.2254

1.1268

2.0282

2.9297

5 (101)

0.1127

0.5634

1.0141

1.4648

6 (110)

0.0563

0.2817

0.5071

0.7324

7 (111)

Until end of packet

As an example, EVENT0=34666, WOR_RES=0 and RX_TIME=6 corresponds to 1.96 ms RX timeout, 1 s polling interval

and 0.195% duty cycle. Note that WOR_RES should be 0 or 1 when using WOR because using WOR_RES > 1 will give a

very low duty cycle. In applications where WOR is not used all settings of WOR_RES can be used.

The duty cycle using WOR is approximated by:

Setting

WOR_RES=0

WOR_RES=1

0 (000)

12.50%

1.95%

1 (001)

6.250%

9765ppm

2 (010)

3.125%

4883ppm

3 (011)

1.563%

2441ppm

4 (100)

0.781%

5 (101)

0.391%

6 (110)

0.195%

7 (111)

Note that the RC oscillator must be enabled in order to use setting 0-6, because the timeout counts RC oscillator

periods. WOR mode does not need to be enabled.

The timeout counter resolution is limited: With RX_TIME=0, the timeout count is given by the 13 MSBs of EVENT0,

decreasing to the 7MSBs of EVENT0 with RX_TIME=6.

CC1100-RTR1 Datasheet(PDF) 73 Page - Texas Instruments

CC1100-RTR1 Datasheet(HTML) 73 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

Datasheet Download

Link URL