| Electronic Components Datasheet Search |
|
AD9864-EB Datasheet(PDF) 16 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD9864-EB Datasheet(HTML) 16 Page - Analog Devices |
|
16 / 44 page ![]() AD9864 Rev. 0 | Page 16 of 44 Address (Hex) Bit Breakdown Width Default Value Name Description 0x13 (7:0) 8 0x3C CKN (7:0) Synthesized frequency divisor (8 LSBs of a 13-bit word). Default yields 300 kHz from 18 MHz; Minimum = 3, Maximum = 8191. 0x14 (6) 1 0 CKF Enable fast acquire. (5) 1 0 CKINV Invert charge pump (0 = source current to increase VCO frequency). (4:2) 3 0x00 CKI Charge pump current in normal operation. IPUMP = (CKI + 1) × 0.625 mA. (1:0) 2 0x03 CKTM Manual control of CLK charge pump (0 = Off, 1 = Up, 2 = Down, and 3 = Normal). 0x15 (5:0) 6 0x00 CKFA (13:8) CK fast acquire time unit (6 LSBs of a 14-bit word). 0x16 (7:0) 8 0x04 CKFA (7:0) CK fast acquire time unit (8 LSBs of a 14-bit word). SSI CONTROL 0x18 (7:0) 8 0x12 SSICRA SSI Control Register A. See Table 8. Default is FS and CLKOUT three-stated. 0x19 (7:0) 8 0x07 SSICRB SSI Control Register B. See Table 8 (16-Bit Data, maximum drive strength). 0x1A (3:0) 4 0x01 SSIORD Output rate divisor. fCLKOUT = fCLK/SSIORD. ADC TUNING 0x1C (1) 1 0 TUNE_LC Perform tuning on LC portion of the ADC (cleared when done). (0) 1 0 TUNE_RC Perform tuning on RC portion of the ADC (cleared when done). 0x1D (3:0) 3 0x00 CAPL1 (2:0) Coarse capacitance setting of LC tank (LSB is 25 pF, differential). 0x1E (5:0) 6 0x00 CAPL0 (5:0) Fine capacitance setting of LC tank (LSB is 0.4 pF, differential). 0x1F (7:0) 8 0x00 CAPR Capacitance setting for RC resonator (64 LSB of fixed capacitance). TEST REGISTERS AND SPI PORT READ ENABLE 0x37–0x39 (7:0) 8 0x00 TEST Factory test mode. Do not use. 0x3A (7:4) 4 0x00 TEST Factory test mode. Do not use. (3) 1 0 SPIREN Enable read from SPI port. (2:0) 3 0x00 TEST Factory test mode. Do not use. 0x3B (7:4) 4 0x00 TEST Factory test mode. Do not use. (3) 1 0 TRI Three-state DOUTB. (2:0) 3 0x00 TEST Factory test mode. Do not use. 0x3C–0x3E (7:0) 8 0x00 TEST Factory Test mode. Do not use. 0x3F (7:0) 8 Subject to Change ID Revision ID (read-only); A write of 0x99 to this register is equivalent to a power-on reset. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |