MCP1711 datasheet(3/36 Pages) MICROCHIP

3 / 36 page

 2015-2016 Microchip Technology Inc.

DS20005415C-page 3

MCP1711

1.0

ELECTRICAL CHARACTERISTICS

Absolute Maximum Ratings †

Input Voltage, VIN.....................................................................................................................................................+6.5V

VIN, SHDN.................................................................................................................................................. -0.3V to +6.5V

Output Current, IOUT (1).........................................................................................................................................470 mA

Output Voltage, VOUT (2)....................................................................................................... -0.3V to VIN + 0.3V or +6.5V

Power Dissipation

5-Lead SOT-23 ..................................................... 600 mW (JEDEC 51-7 FR-4 board with thermal vias) or 250 mW (3)

4-Lead 1 x 1 mm UQFN........................................ 550 mW (JEDEC 51-7 FR-4 board with thermal vias) or 100 mW (3)

Storage Temperature .............................................................................................................................. -55°C to +125°C

Operating Ambient Temperature............................................................................................................... -40°C to +85°C

ESD Protection on all pins ...........................................................................................................±1 kV HBM, ±200V MM

† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.

This is a stress rating only and functional operation of the device at those or any other conditions above those indicated

in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended

periods may affect device reliability.

Note 1: Provided that the device is used in the range of IOUT  PD/(VIN - VOUT).

2: The maximum rating corresponds to the lowest value between VIN + 0.3V or +6.5V.

3: The device is mounted on one layer PCB with minimal copper that does not provide any additional cooling.

DC CHARACTERISTICS

Electrical Characteristics: Unless otherwise indicated, VSHDN = VIN, IOUT = 1 mA, CIN = COUT = 0 µF, VIN = 3.5V for

VR < 2.5V and VIN = VR + 1V for VR  2.5V, TA = +25°C

Parameters

Sym.

Min.

Typ.

Max.

Units

Conditions

Input-Output Characteristics

Input Voltage

VIN

1.4

—

6.0

IOUT = 1 µA

Output Voltage

VOUT

VR - 0.02

VR + 0.02

VR < 2.0V

VR x 0.99

VR x 1.01

VR  2.0V

Maximum Output Current

IOUT

150

—

Load Regulation

VOUT

-16

±3

+16

1 µA

 IOUT  1 mA

-50

±17

+50

1 mA

 IOUT  150 mA

Dropout Voltage (1)

VDROPOUT1

—VDROP1 (2)

VIOUT = 50 mA

VDROPOUT2

—VDROP2 (2)

IOUT = 150 mA

Input Quiescent Current

—

0.60

1.27

µA

VR < 1.9V

—

0.65

1.50

1.9V

 VR < 4.0V

—

0.80

1.80

VR  4.0V

Input Quiescent Current

for SHDN mode

ISHDN

—

0.01

0.10

µA

VIN = 6.0V

VSHDN = VIN

Line Regulation

VOUT/

(

VIN x VOUT)

-0.13

±0.01

+0.13

%/V

IOUT = 1 µA

VR + 0.5V  VIN  6.0V

-0.19

±0.01

+0.19

IOUT = 1 mA

1.2V,VR + 0.5V  VIN 

6.0V

Note 1: The dropout voltage is defined as the input to output differential at which the output voltage drops 2%

below the output voltage value that was measured with an applied input voltage of VIN = VR + 1V.

2: VDROP1, VDROP2: Dropout Voltage (Refer to the DC Characteristics Voltage Table).

MCP1711 Datasheet(PDF) 3 Page - Microchip Technology

MCP1711 Datasheet(HTML) 3 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

Datasheet Download

Link URL