LPC43S30 datasheet(57/156 Pages) NXP

57 / 156 page

LPC43S50_S30_S20

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 1.3 — 20 January 2020

57 of 156

NXP Semiconductors

LPC43S50/S30/S20

32-bit ARM Cortex-M4/M0 microcontroller

Debug pins

DBGEN

[2]

JTAG interface control signal. Also used for boundary scan. To

use the part in functional mode, connect this pin in one of the

following ways:

• Leave DBGEN open. The DBGEN pin is pulled up

internally by a 50 kΩ resistor.

• Tie DBGEN to VDDIO.

• Pull DBGEN up to VDDIO with an external pull-up resistor.

TCK/SWDCLK

[2]

I; F

Test Clock for JTAG interface (default) or Serial Wire (SW)

clock.

TRST

[2]

I; PU I

Test Reset for JTAG interface.

TMS/SWDIO

[2]

I; PU I

Test Mode Select for JTAG interface (default) or SW debug

data input/output.

TDO/SWO

[2]

Test Data Out for JTAG interface (default) or SW trace output.

TDI

[2]

I; PU I

Test Data In for JTAG interface.

USB0 pins

USB0_DP

[6]

I/O USB0 bidirectional D+ line.

USB0_DM

[6]

I/O USB0 bidirectional D

 line.

USB0_VBUS

[6]

[7]

I/O VBUS pin (power on USB cable). This pin includes an internal

pull-down resistor of 64 kΩ (typical)

 16 kΩ.

USB0_ID

[8]

Indicates to the transceiver whether connected as an A-device

(USB0_ID LOW) or B-device (USB0_ID HIGH). For OTG this

pin has an internal pull-up resistor.

USB0_RREF

[8]

12.0 kΩ (accuracy 1 %) on-board resistor to ground for current

reference.

USB1 pins

USB1_DP

F12

D11

[9]

I/O USB1 bidirectional D+ line.

USB1_DM

G12

E11

E10 90

[9]

I/O USB1 bidirectional D

 line.

I2C-bus pins

I2C0_SCL

L15

K13

[10] I; F

I/O I2C clock input/output. Open-drain output (for I2C-bus

compliance).

I2C0_SDA

L16

K14

[10] I; F

I/O I2C data input/output. Open-drain output (for I2C-bus

compliance).

Reset and wake-up pins

RESET

128 [11] I; IA I

External reset input: A LOW-going pulse as short as 50 ns on

this pin resets the device, causing I/O ports and peripherals to

take on their default states, and processor execution to begin

at address 0. This pin does not have an internal pull-up.

WAKEUP0

130 [11] I; IA I

External wake-up input; can raise an interrupt and can cause

wake-up from any of the low-power modes. A pulse with a

duration > 45 ns wakes up the part. This pin does not have an

internal pull-up.

Table 3.

Pin description …continued

LCD, Ethernet, USB0, and USB1 functions are not available on all parts. See Table 2.

Symbol

Description

LPC43S30 Datasheet(PDF) 57 Page - NXP Semiconductors

LPC43S30 Datasheet(HTML) 57 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL