 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
ST72325 Datasheet(PDF) 77 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST72325 Datasheet(HTML) 77 Page - STMicroelectronics |
|
|
77 / 196 page  77/196 16-BIT TIMER (Cont’d) 10.4.3.3 Input Capture In this section, the index, i, may be 1 or 2 because there are two input capture functions in the 16-bit timer. The two 16-bit input capture registers (IC1R and IC2R) are used to latch the value of the free run- ning counter after a transition is detected on the ICAPi pin (see Figure 49). ICiR register is a read-only register. The active transition is software programmable through the IEDGi bit of Control Registers (CRi). Timing resolution is one count of the free running counter: ( fCPU/CC[1:0]). Procedure: To use the input capture function select the follow- ing in the CR2 register: – Select the timer clock (CC[1:0]) (see Table 18 Clock Control Bits). – Select the edge of the active transition on the ICAP2 pin with the IEDG2 bit (the ICAP2 pin must be configured as floating input or input with pull-up without interrupt if this configuration is available). And select the following in the CR1 register: – Set the ICIE bit to generate an interrupt after an input capture coming from either the ICAP1 pin or the ICAP2 pin – Select the edge of the active transition on the ICAP1 pin with the IEDG1 bit (the ICAP1pin must be configured as floating input or input with pull- up without interrupt if this configuration is availa- ble). When an input capture occurs: – ICFi bit is set. – The ICiR register contains the value of the free running counter on the active transition on the ICAPi pin (see Figure 50). – A timer interrupt is generated if the ICIE bit is set and the I bit is cleared in the CC register. Other- wise, the interrupt remains pending until both conditions become true. Clearing the Input Capture interrupt request (that is, clearing the ICFi bit) is done in two steps: 1. Reading the SR register while the ICFi bit is set. 2. An access (read or write) to the ICiLR register. Notes: 1. After reading the ICiHR register, transfer of input capture data is inhibited and ICFi will never be set until the ICiLR register is also read. 2. The ICiR register contains the free running counter value which corresponds to the most recent input capture. 3. The two input capture functions can be used together even if the timer also uses the two out- put compare functions. 4. In One Pulse mode and PWM mode only Input Capture 2 can be used. 5. The alternate inputs (ICAP1 and ICAP2) are always directly connected to the timer. So any transitions on these pins activates the input capture function. Moreover if one of the ICAPi pins is configured as an input and the second one as an output, an interrupt can be generated if the user tog- gles the output pin and if the ICIE bit is set. This can be avoided if the input capture func- tion i is disabled by reading the ICiHR (see note 1). 6. The TOF bit can be used with interrupt genera- tion in order to measure events that go beyond the timer range (FFFFh). MS Byte LS Byte ICiR ICiHR ICiLR |
Similar Part No. - ST72325_07 |
|
Similar Description - ST72325_07 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
