Electronic Components Datasheet Search
  English  ▼

X  

TMS320VC5420 Datasheet(PDF) 9 Page - Texas Instruments

Part # TMS320VC5420
Description  FIXED-POINT DIGITAL SIGNAL PROCESSOR
PDF  77 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI [Texas Instruments]
Direct Link  http://www.ti.com
Logo TI - Texas Instruments

TMS320VC5420 Datasheet(HTML) 9 Page - Texas Instruments

Back Button TMS320VC5420 Datasheet HTML 5Page - Texas Instruments TMS320VC5420 Datasheet HTML 6Page - Texas Instruments TMS320VC5420 Datasheet HTML 7Page - Texas Instruments TMS320VC5420 Datasheet HTML 8Page - Texas Instruments TMS320VC5420 Datasheet HTML 9Page - Texas Instruments TMS320VC5420 Datasheet HTML 10Page - Texas Instruments TMS320VC5420 Datasheet HTML 11Page - Texas Instruments TMS320VC5420 Datasheet HTML 12Page - Texas Instruments TMS320VC5420 Datasheet HTML 13Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 77 page
background image
TMS320VC5420
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SPRS080C – MARCH 1999 – REVISED APRIL 2000
9
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
signal descriptions
The ’5420 signal descriptions table lists each pin name, function, and operating mode(s) for the ’5420 device.
Some of the ’5420 pins can be configured for one of two functions; a primary function and a secondary function.
The names of these pins in secondary mode are shaded in grey in the following table.
Signal Descriptions
NAME
TYPE†
DESCRIPTION
DATA SIGNALS
PPA17 (MSB)
PPA16
PPA15
PPA15
PPA14
PPA13
PPA12
Parallel port address bus. The DSP can access the external memory locations by way of the external memory
PPA12
PPA11
PPA10
PPA9
I/O/Z
Parallel ort address bus. The DSP can access the external memory locations by way of the external memory
interface using PPA[17:0] in external memory interface (EMIF) mode when the XIO pin is logic high.
The PPA[17:0] pins are also multiplexed with the HPI interface. In HPI mode (XIO pin is low), the external address
PPA9
PPA8
PPA7
PPA6
I/O/Z
The PPA[17:0] ins are also multi lexed with the HPI interface. In HPI mode (XIO in is low), the external address
pins PPA[17:0] are used by a host processor for access to the memory map by way of the on-chip HPI. Refer
to the HPI section of this table for details on the secondary functions of these pins.
PPA6
PPA5
PPA4‡§
PPA3
These pins are placed into the high-impedance state when OFF is low.
PPA3
PPA2
PPA1
PPA0 (LSB)
PPD15 (MSB)
PPD14
PPD13
PPD12
PPD11
PPD10
PPD9
PPD8
PPD7
PPD6
PPD5
PPD4
PPD3
PPD2
PPD1
PPD0 (LSB)
I/O/Z¶
Parallel port data bus. The DSP uses this bidirectional data bus to access external memory when the device is
in external memory interface (EMIF) mode (the XIO pin is logic high).
This data bus is also multiplexed with the 16-bit HPI data bus. When in HPI mode, the bus is used to transfer data
between the host processor and internal DSP memory via the HPI. Refer to the HPI section of this table for details
on the secondary functions of these pins.
The data bus includes bus holders to reduce power dissipation caused by floating, unused pins. The bus holders
also eliminate the need for external pullup resistors on unused pins. When the data bus is not being driven by
the ’5420, the bus holders keep data pins at the last driven logic level. The data bus keepers are disabled at reset
and can be enabled/disabled via the BH bit of the BSCR register.
These pins are placed into high-impedance state when OFF is low.
INITIALIZATION, INTERRUPT, AND RESET OPERATIONS
A_INT0§
B_INT0§
A_INT1§
B_INT1§
I
External user interrupts. INT0–INT3 are prioritized and are maskable by the interrupt mask register (IMR) and
the interrupt mode bit. INT0 –INT3 can be polled and reset by way of the interrupt flag register (IFR).
A_NMI§
B_NMI§
I
Nonmaskable interrupt. NMI is an external interrupt that cannot be masked by way of the INTM or the IMR. When
NMI is activated, the processor traps to the appropriate vector location.
† I = Input, O = Output, S = Supply, Z = High Impedance
‡ This pin has an internal pullup resistor.
§ These pins have Schmitt trigger inputs.
¶ This pin has an internal bus holder controlled by way of the BSCR register in subchip A.
# This pin is used by Texas Instruments for device testing and should be left unconnected.
|| This pin has an internal pulldown resistor.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com