| Electronic Components Datasheet Search |
|
DS1863 Datasheet(PDF) 4 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
DS1863 Datasheet(HTML) 4 Page - Maxim Integrated Products |
|
4 / 62 page ![]() Burst-Mode PON Controller With Integrated Monitoring 4 _____________________________________________________________________ NONVOLATILE MEMORY CHARACTERISTICS (VCC = +2.85V to +3.9V, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS EEPROM Write Cycles +70°C 50,000 I2C AC ELECTRICAL CHARACTERISTICS (VCC = +2.85V to +3.9V, TA = -40°C to +95°C, unless otherwise noted, see Figure 9.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS SCL Clock Frequency fSCL (Note 12) 0 400 kHz Clock Pulse-Width Low tLOW 1.3 µs Clock Pulse-Width High tHIGH 0.6 µs Bus Free Time Between STOP and START Condition tBUF 1.3 µs START Hold Time tHD:STA 0.6 µs START Setup Time tSU:STA 0.6 µs Data-In Hold Time tHD:DAT 0 0.9 µs Data-In Setup Time tSU:DAT 100 ns Rise Time of Both SDA and SCL Signals t R (Note 13) 20 + 0.1CB 300 ns Fall Time of Both SDA and SCL Signals t F (Note 13) 20 + 0.1CB 300 ns STOP Setup Time tSU:STO 0.6 µs Capacitive Load for Each Bus Line CB (Note 13) 400 pF EEPROM Write Time tW (Note 14) 20 ms Note 1: All voltages are referenced to ground. Currents into the IC are positive and out of the IC are negative. Note 2: Digital Inputs are at rail. FETG is disconnected SDA = SCL = 1. Note 3: See the Safety Shutdown (FETG) Output section for details. Note 4: Eight ranges allow the full-scale range to change from 625mV to 2.5V. Note 5: This specification applies to the expected full-scale value for the selected range. See the Comp Ranging byte for available full-scale ranges. Note 6: Eight ranges allow the full-scale range to change from 312.5mV to 1.25V. Note 7: The output impedance of the DS1863 is proportional to its scale setting. For instance, if using the 1/2 scale, the output impedance would be 1.5k Ω. Note 8: This specification applies to the expected full-scale value for the selected range. See the Mod Ranging byte for available full-scale ranges. Note 9: See the APC/Quick-Trip Sample Timing section for details. Note 10: Assuming an appropriate initial step is programmed that would cause the power to exceed the APC set point within 4 steps, the bias current will be within 1% within the time specified by the binary search time. Note 11: Guaranteed by design. Note 12: I2C interface timing shown is for fast-mode (400kHz) operation. This device is also backward-compatible with I2C stan- dard-mode timing. Note 13: CB—total capacitance of one bus line in picofarads. Note 14: EEPROM write begins after a STOP condition occurs. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |