ATmega88 datasheet(138/340 Pages) ATMEL

138 / 340 page

138

7530H–AVR–02/09

ATmega48/88/168 Automotive

The OCR2x Register is double buffered when using any of the Pulse Width Modulation (PWM)

modes. For the Normal and Clear Timer on Compare (CTC) modes of operation, the double

buffering is disabled. The double buffering synchronizes the update of the OCR2x Compare

occurrence of odd-length, non-symmetrical PWM pulses, thereby making the output glitch-free.

The OCR2x Register access may seem complex, but this is not case. When the double buffering

is enabled, the CPU has access to the OCR2x Buffer Register, and if double buffering is dis-

abled the CPU will access the OCR2x directly.

15.4.1

Force Output Compare

In non-PWM waveform generation modes, the match output of the comparator can be forced by

writing a one to the Force Output Compare (FOC2x) bit. Forcing compare match will not set the

OCF2x Flag or reload/clear the timer, but the OC2x pin will be updated as if a real compare

match had occurred (the COM2x1:0 bits settings define whether the OC2x pin is set, cleared or

toggled).

15.4.2

Compare Match Blocking by TCNT2 Write

All CPU write operations to the TCNT2 Register will block any compare match that occurs in the

next timer clock cycle, even when the timer is stopped. This feature allows OCR2x to be initial-

ized to the same value as TCNT2 without triggering an interrupt when the Timer/Counter clock is

enabled.

15.4.3

Using the Output Compare Unit

Since writing TCNT2 in any mode of operation will block all compare matches for one timer clock

cycle, there are risks involved when changing TCNT2 when using the Output Compare channel,

independently of whether the Timer/Counter is running or not. If the value written to TCNT2

equals the OCR2x value, the compare match will be missed, resulting in incorrect waveform

generation. Similarly, do not write the TCNT2 value equal to BOTTOM when the counter is

downcounting.

The setup of the OC2x should be performed before setting the Data Direction Register for the

port pin to output. The easiest way of setting the OC2x value is to use the Force Output Com-

pare (FOC2x) strobe bit in Normal mode. The OC2x Register keeps its value even when

changing between Waveform Generation modes.

Be aware that the COM2x1:0 bits are not double buffered together with the compare value.

Changing the COM2x1:0 bits will take effect immediately.

15.5

Compare Match Output Unit

The Compare Output mode (COM2x1:0) bits have two functions. The Waveform Generator uses

the COM2x1:0 bits for defining the Output Compare (OC2x) state at the next compare match.

Also, the COM2x1:0 bits control the OC2x pin output source. Figure 15-4 shows a simplified

schematic of the logic affected by the COM2x1:0 bit setting. The I/O Registers, I/O bits, and I/O

pins in the figure are shown in bold. Only the parts of the general I/O Port Control Registers

(DDR and PORT) that are affected by the COM2x1:0 bits are shown. When referring to the

OC2x state, the reference is for the internal OC2x Register, not the OC2x pin.

ATmega88 Datasheet(PDF) 138 Page - ATMEL Corporation

ATmega88 Datasheet(HTML) 138 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL