ATmega88 datasheet(209/340 Pages) ATMEL

209 / 340 page

209

7530H–AVR–02/09

ATmega48/88/168 Automotive

19.5.2

Bit Rate Generator Unit

This unit controls the period of SCL when operating in a Master mode. The SCL period is con-

trolled by settings in the TWI Bit Rate Register (TWBR) and the Prescaler bits in the TWI Status

CPU clock frequency in the Slave must be at least 16 times higher than the SCL frequency. Note

that slaves may prolong the SCL low period, thereby reducing the average TWI bus clock

period. The SCL frequency is generated according to the following equation:

• TWBR = Value of the TWI Bit Rate Register.

• PrescalerValue = Value of the prescaler, see Table 19-2 on page 212.

Note:

TWBR should be 10 or higher if the TWI operates in Master mode. If TWBR is lower than 10, the

Master may produce an incorrect output on SDA and SCL for the reminder of the byte. The prob-

lem occurs when operating the TWI in Master mode, sending Start + SLA + R/W to a Slave (a

Slave does not need to be connected to the bus for the condition to happen).

19.5.3

Bus Interface Unit

This unit contains the Data and Address Shift Register (TWDR), a START/STOP Controller and

Arbitration detection hardware. The TWDR contains the address or data bytes to be transmitted,

or the address or data bytes received. In addition to the 8-bit TWDR, the Bus Interface Unit also

contains a register containing the (N)ACK bit to be transmitted or received. This (N)ACK Regis-

ter is not directly accessible by the application software. However, when receiving, it can be set

or cleared by manipulating the TWI Control Register (TWCR). When in Transmitter mode, the

value of the received (N)ACK bit can be determined by the value in the TWSR.

The START/STOP Controller is responsible for generation and detection of START, REPEATED

START, and STOP conditions. The START/STOP controller is able to detect START and STOP

conditions even when the AVR MCU is in one of the sleep modes, enabling the MCU to wake up

if addressed by a Master.

If the TWI has initiated a transmission as Master, the Arbitration Detection hardware continu-

ously monitors the transmission trying to determine if arbitration is in process. If the TWI has lost

an arbitration, the Control Unit is informed. Correct action can then be taken and appropriate

status codes generated.

19.5.4

Address Match Unit

The Address Match unit checks if received address bytes match the seven-bit address in the

TWI Address Register (TWAR). If the TWI General Call Recognition Enable (TWGCE) bit in the

TWAR is written to one, all incoming address bits will also be compared against the General Call

address. Upon an address match, the Control Unit is informed, allowing correct action to be

taken. The TWI may or may not acknowledge its address, depending on settings in the TWCR.

The Address Match unit is able to compare addresses even when the AVR MCU is in sleep

mode, enabling the MCU to wake up if addressed by a Master. If another interrupt (e.g., INT0)

occurs during TWI Power-down address match and wakes up the CPU, the TWI aborts opera-

tion and return to it’s idle state. If this cause any problems, ensure that TWI Address Match is the

only enabled interrupt when entering Power-down.

SCL frequency

CPU Clock frequency

2(TWBR)

PrescalerValue

()

⋅

--------------------------------------------------------------------------------------------

ATmega88 Datasheet(PDF) 209 Page - ATMEL Corporation

ATmega88 Datasheet(HTML) 209 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL