LPC2364 datasheet(21/69 Pages) NXP

21 / 69 page

LPC2364_65_66_67_68

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 7.1 — 16 October 2013

21 of 69

NXP Semiconductors

LPC2364/65/66/67/68

Single-chip 16-bit/32-bit microcontrollers

FIQs have the highest priority. If more than one request is assigned to FIQ, the VIC ORs

the requests to produce the FIQ signal to the ARM processor. The fastest possible FIQ

latency is achieved when only one request is classified as FIQ, because then the FIQ

service routine can simply start dealing with that device. But if more than one request is

assigned to the FIQ class, the FIQ service routine can read a word from the VIC that

identifies which FIQ source(s) is (are) requesting an interrupt.

Vectored IRQs, which include all interrupt requests that are not classified as FIQs, have a

programmable interrupt priority. When more than one interrupt is assigned the same

priority and occur simultaneously, the one connected to the lowest numbered VIC channel

will be serviced first.

The VIC ORs the requests from all of the vectored IRQs to produce the IRQ signal to the

ARM processor. The IRQ service routine can start by reading a register from the VIC and

jumping to the address supplied by that register.

7.5.1 Interrupt sources

Each peripheral device has one interrupt line connected to the VIC but may have several

interrupt flags. Individual interrupt flags may also represent more than one interrupt

source.

Any pin on Port 0 and Port 2 (total of 42 pins) regardless of the selected function, can be

programmed to generate an interrupt on a rising edge, a falling edge, or both. Such

interrupt request coming from Port 0 and/or Port 2 will be combined with the EINT3

interrupt requests.

7.6 Pin connect block

The pin connect block allows selected pins of the microcontroller to have more than one

function. Configuration registers control the multiplexers to allow connection between the

pin and the on chip peripherals.

Peripherals should be connected to the appropriate pins prior to being activated and prior

to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is

not mapped to a related pin should be considered undefined.

7.7 General purpose DMA controller

The GPDMA is an AMBA AHB compliant peripheral allowing selected

LPC2364/65/66/67/68 peripherals to have DMA support.

The GPDMA enables peripheral-to-memory, memory-to-peripheral,

peripheral-to-peripheral, and memory-to-memory transactions. Each DMA stream

provides unidirectional serial DMA transfers for a single source and destination. For

example, a bidirectional port requires one stream for transmit and one for receive. The

source and destination areas can each be either a memory region or a peripheral, and

can be accessed through the AHB master.

7.7.1 Features

• Two DMA channels. Each channel can support a unidirectional transfer.

• The GPDMA can transfer data between the 8 kB SRAM and peripherals such as the

SD/MMC, two SSP, and I2S interfaces.

LPC2364 Datasheet(PDF) 21 Page - NXP Semiconductors

LPC2364 Datasheet(HTML) 21 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

Datasheet Download

Link URL