Electronic Components Datasheet Search
  English  ▼

X  

PC7410 Datasheet(PDF) 43 Page - ATMEL Corporation

Part # PC7410
Description  PowerPC 7410 RISC Microprocessor Product Specification
PDF  54 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  ATMEL [ATMEL Corporation]
Direct Link  http://www.atmel.com
Logo ATMEL - ATMEL Corporation

PC7410 Datasheet(HTML) 43 Page - ATMEL Corporation

Back Button PC7410 Datasheet HTML 39Page - ATMEL Corporation PC7410 Datasheet HTML 40Page - ATMEL Corporation PC7410 Datasheet HTML 41Page - ATMEL Corporation PC7410 Datasheet HTML 42Page - ATMEL Corporation PC7410 Datasheet HTML 43Page - ATMEL Corporation PC7410 Datasheet HTML 44Page - ATMEL Corporation PC7410 Datasheet HTML 45Page - ATMEL Corporation PC7410 Datasheet HTML 46Page - ATMEL Corporation PC7410 Datasheet HTML 47Page - ATMEL Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 43 / 54 page
background image
43
PC7410
2141D–HIREL–02/04
Figure 31. Driver Impedance Measurement
Table 19 summarizes the signal impedance results. The impedance increases with junc-
tion temperature and is relatively unaffected by bus voltage.
Pull-up Resistor
Requirements
The PC7410 requires pull-up resistors (1 k
Ω–5 kΩ) on several control pins of the bus
interface to maintain the control signals in the negated state after they have been
actively negated and released by the PC7410 or other bus masters. These pins are: TS,
ARTRY, SHDO, SHD1.
Four test pins also require pull-up resistors (100
Ω–1 kΩ). These pins are CHK,
L1_TSTCLK, L2_TSTCLK, and LSSD_MODE. These signals are for factory use only
and must be pulled up to OV
DD for normal machine operation.
If pull-down resistors are used to configure BVSEL or L2VSEL, the resistors should be
less than 250
Ω. (see Table 12). Because PLL_CFG[0:3] must remain stable during nor-
mal operation, strong pull-up and pull-down resistors (1 k
Ω or less) are recommended to
configure these signals in order to protect against erroneous switching due to ground
bounce, power supply noise or noise coupling.
In addition, CKSTP_OUT is an open-drain style output that requires a pull-up resistor
(1 k
Ω–5 kΩ) if it is used by the system. The CKSTP_IN signal should likewise be pulled
up through a pull-up resistor (1 k
Ω–5 kΩ) to prevent erroneous assertions of this signal.
Table 19. Impedance Characteristics with V
DD = 1.8V, OVDD = 1.8V or 2.5V,
T
j = -55°C to 125°C
Impedance
Processor bus
L2 Bus
Symbol
Unit
RN
41.5 - 54.3
42.7 - 54.1
Z
0
Ohms
RP
37.3 - 55.3
39.3 - 50
Z0
Ohms
OVDD
OGND
SW2
SW1
RN
RP
Pad
Data



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com