| Electronic Components Datasheet Search |
|
CD1283 Datasheet(PDF) 28 Page - Intel Corporation |
|
|
|||||||||||||||||||||||||||||
CD1283 Datasheet(HTML) 28 Page - Intel Corporation |
|
28 / 94 page ![]() CD1283 — IEEE 1284-Compatible Parallel Interface 28 Datasheet • IDReq for slave ID requests from the remote master. • nINIT for initialization pulses from the master (Compatibility mode only) Any or all of these bits may be set, based on the mode of operation. The NegCh interrupt is issued whenever the remote master performs a protocol change, such as moving from Compatibility mode to ECP; the CPU examines the NSR to determine the new state of the parallel interface. Signal changes can be identified by reading the SSR. In response to the EPPAW interrupt, the CPU would read the EAR to retrieve the value that was written during the EPP address write cycle. Figure 5. Interrupt Generation Logic FAILED NEG. (INVALID EXTCODE) [COMPATIBILITY MODE] NSR=0x41 TERMINATION [COMPATIBILITY MODE] NSR=0x82 NEG-OK NSR=0x86[EPP MODE] {40} NSR=0x88[RN MODE] {00} NSR=0x8A[RB MODE] {01} NSR=0x8C[ECP w/o RLE]{10} NSR=0x8E[ECP w/ RLE] {30} NEG-OK NSR=0x89[RN ID REQUEST] {04} NSR=0x8B[RB ID REQUEST] {05} NSR=0x8D[ECP w/o RLE ID REQUEST]{14} NSR=0x8F[ECP w/ RLE ID REQUEST] {34} IDReq PCISR[1] NegCh PCISR[5] IDReq PCIER[1] NegCh PCIER[5] FAILED NEG MODE NOT ENABLED [COMPATIBILITY MODE] NSR=0x46 (EPP) NSR=0x48 (RN) NSR=0x49 (RN-ID) NSR=0x4A (RB) NSR=0x4B (RB-ID) NSR=0x4C (ECP) NSR=0x4D (ECP-ID) NSR=0x4E (ECP-RLE) NSR=0x4F (ECP-RLE-ID) HOST TIMEOUT HOST HAS NOT RESPONDED FOR OVER 1 SEC.) [COMPATIBILITY MODE] NSR=0x22 INVALID HOST HAS VIOLATED HANDSHAKING SEQUENCE [COMPATIBILITY MODE] NSR=0x16 (EPP) NSR=0x18 (RN) NSR=0x19 (RN-ID) NSR=0x1A (RB) NSR=0x1B (RB-ID) NSR=0x1C (ECP) NSR=0x1D (ECP-ID) NSR=0x1E (ECP-RLE) NSR=0x1F (ECP-RLE-ID) NOTE: An immediate termination from the host gener- ates this interrupt NOTE: ID requests fail if either the negotiation type or RID is disabled in NER. Other negotiations also fail if the negotiation type is disabled. KEY: [ ] = Current mode { } = Interface extensibility request value (see IEEE1284 Std for more details) (register name[x]) : x = bit #, that is PCIER[1] = PCIER, bit 1 ( |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |