Electronic Components Datasheet Search
  English  ▼

X  

LTC6820 Datasheet(PDF) 34 Page - Analog Devices

Part # LTC6820
Description  Current, Voltage, and Charge Monitor for High Voltage Battery Packs
PDF  80 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

LTC6820 Datasheet(HTML) 34 Page - Analog Devices

Back Button LTC6820 Datasheet HTML 30Page - Analog Devices LTC6820 Datasheet HTML 31Page - Analog Devices LTC6820 Datasheet HTML 32Page - Analog Devices LTC6820 Datasheet HTML 33Page - Analog Devices LTC6820 Datasheet HTML 34Page - Analog Devices LTC6820 Datasheet HTML 35Page - Analog Devices LTC6820 Datasheet HTML 36Page - Analog Devices LTC6820 Datasheet HTML 37Page - Analog Devices LTC6820 Datasheet HTML 38Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 34 / 80 page
background image
LTC2949
34
Rev A
For more information www.analog.com
Commands Compatible with LTC68xx Cell Monitors
(RDCV, ADCV)
The LTC2949 supports several RDCV and ADCV style
commands compatible with LTC68xx Cell Monitors.
RDCVA-RDCVF,RDAUXA-RDAUXD,RDCFGA,RDCFGB(all
referred as RDCV commands in this document), ADCV,
ADOW, ADOL, ADAX, ADAXD, ADCVAX and ADCVSC (all
referred as ADCV commands in this document) are sup-
portedasbroadcastandaddressedcommands.Addressed
commands are used to address LTC2949 exclusively. To
trigger actions on LTC2949 and LTC68xx Cell Monitors
simultaneously, broadcast commands are used. This is
for example useful to initiating ADC conversions of several
devices at the same time. No matter if LTC2949 is con-
nected parallel to or on top of a daisy chain, addressed
ADCV commands can trigger measurements on LTC2949
only and broadcast ADCV commands can perform syn-
chronous ADC conversions on all devices connected to
the SPI / isoSPI bus. The conversion starts at the end of
the PEC for all devices.
In cases where LTC2949 is connected parallel to a daisy
chain, direct read commands (DCMD) must be used
to read register data and addressed RDCV commands
(with RDCVCONF=1) must be used to read the last fast
conversion results. If LTC2949 is connected on top of a
daisy chain, broadcast RDCV commands must be used
to read register data (RDCVCONF=0) or to read the last
fast conversion results (RDCVCONF=1) depending on
setting of REGSCTRL.RDCVCONF. Write to LTC2949’s
register map is always done with direct write commands
(DCMD) independent of the bus topology. See Table 10
(Communication with LTC2949) for a summary of all
possible communication scenarios.
Before LTC2949 can react on ADCV commands it must be
runninginslowcontinuousmeasurementmode(bitCONT
in OPCTRL), at least one fast measurement channel must
be selected via the Fast Control Register (FACTRL) and
optionally, to make also fast BAT conversions via one of
the power ADCs (P1 or P2 in voltage mode), P1ASV and/
or P2ASV in the ADC configuration register (ADCCONF)
must be set. If LTC2949 is running in fast continuous
mode (FACONV=1) any ADCV command is ignored and
SERIAL INTERFACES
acquired samples can be read from the FIFO registers (FI-
FOI1, FIFOI2, FIFOBAT, FIFOAUX). Still, also in this mode,
it is possible to read the last fast conversion results via
RDCV(RDCVCONF=1).Iffastcontinuousmodeisdisabled
(FACONV=0), any ADCV command will clear all FIFOs.
If needed, samples within FIFOs should be read before
sending an ADCV command while FACONV is cleared.
In the configuration where LTC2949 is on top of a daisy
chain, after a broadcast RDCV command, the stacked
LTC68xxCellMonitorsturnintoacascadedshiftregister,in
whichdataisshiftedthrougheachdevicetothenextdevice
in the stack. In this scenario, LTC2949 responds to RDCV
commands only if the Broadcast Read Enable bit (BCREN)
in the Register Control Register (REGSCTRL) is set.
In the scenario where LTC2949 is placed in parallel to
a daisy chain of LTC68xx Cell Monitors, the bit BCREN
must be cleared (default) to avoid bus collisions. Still,
any broadcast RDCV may clear LTC2949's internal HS
byte (see below) if the bit RDCVCONF is set, no matter if
BCREN is set or not. For this reason, it is recommended
to read LTC2949’s fast conversion results before reading
from the LTC68xx Cell Monitors. Or, if for software tim-
ing reasons it is necessary to read from the LTC68xx Cell
Monitors first, the bit RDCVCONF must be cleared before
(it must be set again afterwards to read fast conversion
data from LTC2949).
The last results of any fast conversion can be read out by
the RDCV command, providing sequentially the results
of I1, I2, BAT and AUX (least significant bytes first to be
compatible with LTC68xx Cell Monitors) followed by one
or more hand shake (HS) bytes, indicating if the data is
new (0x0F) or old (0x00). Once LTC2949 sends the HS
byte, it will continue sending it as long as the master is
reading bytes. Still, a PEC will always be send for every 6
data bytes. Per transaction, the HS byte may only change
from 0x00 to 0x0F, once it is 0x0F it won’t change. This
allows the master to poll for conversion results being
ready by checking for a transition of the HS byte from
0x00 to 0x0F. If the first HS byte is 0x0F the conversion
data received with that command is already new and valid.
If the first HS byte is 0x00 the data received in the same
transaction was not yet updated. A subsequent RDCV



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com