Electronic Components Datasheet Search
  English  ▼

X  

LTC6820 Datasheet(PDF) 9 Page - Analog Devices

Part # LTC6820
Description  Current, Voltage, and Charge Monitor for High Voltage Battery Packs
PDF  80 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

LTC6820 Datasheet(HTML) 9 Page - Analog Devices

Back Button LTC6820 Datasheet HTML 5Page - Analog Devices LTC6820 Datasheet HTML 6Page - Analog Devices LTC6820 Datasheet HTML 7Page - Analog Devices LTC6820 Datasheet HTML 8Page - Analog Devices LTC6820 Datasheet HTML 9Page - Analog Devices LTC6820 Datasheet HTML 10Page - Analog Devices LTC6820 Datasheet HTML 11Page - Analog Devices LTC6820 Datasheet HTML 12Page - Analog Devices LTC6820 Datasheet HTML 13Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 80 page
background image
LTC2949
9
Rev A
For more information www.analog.com
ELECTRICAL CHARACTERISTICS The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
I2C Interface Timing Specification (SCL, SDA)
fSCL(MAX)
Maximum SCL Clock Frequency
l
8
10
kHz
tSCLLO
SCL Low Period
l
80
µs
tSDALO
SDA Low Period
l
80
µs
tBUF(MIN)
Bus Free Time Between STOP/START
l
30
µs
tSU,STA(MIN) Minimum Repeated START Setup Time
l
30
µs
tHD,STA(MIN) Minimum Hold Time (Repeated) START
Condition
l
30
µs
tSU,STO(MIN) Minimum Setup Time for STOP Condition
l
30
µs
tSU,DAT(MIN) Minimum Data Setup Time Input
l
30
µs
tHD,DAT(MIN) Minimum Data Hold Time Input
l
0
ns
tHD,DATO
Minimum Data Hold Time Output
l
30
µs
tOF
Data Output Fall Time
(Notes 7, 8)
l
20 + 0.1
• CB
ns
Digital Core Timings (See Figure 3)
tBOOT
Core Boot-Up Time from SLEEP or POWER-OFF
to STANDBY
AVCC/DVCC Pins at Minimum Operating
Voltage
l
100
ms
tIDLE_CORE Core STANDBY Cycle Time
(Note 10)
l
17
20
ms
tCONT
Core MEASURE Cycle Time
(Note 11)
l
90
100
110
ms
tMLCK,M
Memory Lock Request to Acknowledge Time
Core Status MEASURE
l
130
ms
tMLCK,S
Memory Lock Request to Acknowledge Time
Core Status STANDBY
l
40
ms
tACKN
Time from Core Entering STANDBY to Return to
SLEEP, When Wake-Up is not Confirmed
No Write of 0x0 to Reg. WKUPACK, No
Write of 0x8 to Reg. OPCTRL
l
0.6
1.5
s
Time Base
TUETB
TUE Time Base
Internal Clock
0.5
%
l
1
%
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect the device
reliability and lifetime.
Note 2: Positive currents flow into pins, negative currents flow out of pins.
Minimum and maximum values refer to absolute values.
Note 3: Do not apply a voltage or current source to these pins. They must
be unconnected, connected to capacitive loads or connected to a crystal
according to their pin description. Otherwise permanent damage may
occur.
Note 4: Do not apply a voltage source to these pins. Overloading these
pins might disrupt operation.
Note 5: Active supply current (ICC) is dependent on the amount of time
that the output drivers are active on IP and IM. During those times ICC will
increase by the 20 • IB drive current. For the maximum data rate 1MHz, the
drivers are active approximately 5% of the time.
Note 6: These timing specifications are dependent on the delay through
the cable, and include allowances for 50ns of delay each direction. 50ns
corresponds to 10m of CAT-5 cable (which has a velocity of propagation of
66% the speed of light). Use of longer cables would require derating these
specs by the amount of additional delay.
Note 7: Guaranteed by design and characterization, not subject to
production test.
Note 8: CB = capacitance of one bus line in pf (10pF < CB < 400pF)
Note 9: These specifications do not include rise time of SDO due to pull up
resistance and load capacitance on SDO pin.
Note 10: Cycle time at which STATUS/FAULTS and VREF registers are
updated.
Note 11: Cycle time at which STATUS/ALERT/FAULTS registers and all
slow channel measurement results are updated after the first update. The
first update after enabling any measurement is typically 50ms delayed.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com