Electronic Components Datasheet Search
  English  ▼

X  

TMP1826 Datasheet(PDF) 13 Page - Texas Instruments

Click here to check the latest version.
Part # TMP1826
Description  TMP1826 Single-Wire, ±0.3°C Accurate Temperature Sensor With 2-kbit EEPROM
PDF  71 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI [Texas Instruments]
Direct Link  http://www.ti.com
Logo TI - Texas Instruments

TMP1826 Datasheet(HTML) 13 Page - Texas Instruments

Back Button TMP1826 Datasheet HTML 9Page - Texas Instruments TMP1826 Datasheet HTML 10Page - Texas Instruments TMP1826 Datasheet HTML 11Page - Texas Instruments TMP1826 Datasheet HTML 12Page - Texas Instruments TMP1826 Datasheet HTML 13Page - Texas Instruments TMP1826 Datasheet HTML 14Page - Texas Instruments TMP1826 Datasheet HTML 15Page - Texas Instruments TMP1826 Datasheet HTML 16Page - Texas Instruments TMP1826 Datasheet HTML 17Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 71 page
background image
and the external pullup resistor can charge the internal capacitor during bus idle time. If the internal voltage on
the capacitor drops below the brown-out threshold, the device shall switch itself off and enter bus powered mode
of communication on subsequent power up. The device may not complete the ongoing communication during
this time. When the device completes the power-up initialization sequence, as described earlier, the device shall
respond to first bus communication starting with the bus reset sequence.
7.3.3 Bus Pullup Resistor
The bus pullup resistance value selected is important for communication as per the speed mode and ensuring
that minimal possible energy is consumed in the application. If the resistor value is too small, it may violate the
VOL limits on the SDQ pin.
The total SDQ pin and bus capacitance must be considered along with the bus leakage current when selecting
the pullup resistor. The pullup resistance value selected must also ensure that the signal level reaches VIH as
per the timing requirements for standard and overdrive mode.
In bus powered mode of operation, the device charges its internal capacitor through the SDQ pin and the pullup
resistor. This charge on the capacitor is used during bus communication, when the SDQ pin low. For other high
current functions like thermal conversion and EEPROM access, the bus is held idle to ensure that the device
can draw current through the pullup resistor. The SDQ pin voltage during the high current operation must be
maintained to ensure sufficient operating margins. Use Equation 1 to calculate the pullup resistor value.
VPUR − VOLMAX
4 × 10−3  <RPUR< VPUR − 1.6
IPUMIN
(1)
When the device is used in VDD or supply powered mode, a larger pullup resistor value may be used, as the
SDQ pin is used only for communication. The user must ensure that the pullup resistor value selected must be
able to support the timing for the required bus speed of operation.
For low current consumption devices like the TMP1826, selecting the correct pullup resistor value allows
the application to avoid low impedance current path components for bus powered mode of operation while
maintaining communication speeds and device parameters as per its electrical specification.
7.3.4 Temperature Results
The conversion is initiated by the host MCU by sending the temperature conversion command if the automatic
conversion is disabled, or immediately after the presence detect is completed when the automatic conversion is
enabled, or in continuous conversion mode if the device is VDD powered. At the end of every conversion, the
device updates the temperature registers temperature result and the status register bits. Figure 7-2 shows that
the device supports a high precision and legacy format, which can be configured through the TEMP_FMT bit in
the device configuration-1 register.
2
4
2
5
2
6
S
S
S
S
S
2
-4
2
-3
2
-2
2
-1
2
0
2
1
2
2
2
3
2
1
2
2
2
3
2
4
2
5
2
6
2
7
S
2
-7
2
-6
2
-5
2
-4
2
-3
2
-2
2
-1
2
0
Temperature Result MSB Register
Temperature Result LSB Register
High Precision Format
Legacy Format
Figure 7-2. Temperature Format
If the format selected is the high precision 16-bit format, the data in the result registers is stored in two's
complement form and has a resolution of 0.0078125°C. If the format selected is the legacy 12-bit format, the
data in the result register is stored in sign extended form and has a resolution of 0.0625°C. The temperature
register reads as 0°C before the first conversion. Table 7-1 and Table 7-2 show examples of possible binary
data that can be read from the temperature result registers and the corresponding hexadecimal and temperature
equivalents for both formats.
www.ti.com
TMP1826
SBOSA45A – FEBRUARY 2022 – REVISED SEPTEMBER 2022
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TMP1826



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com