CS5920 datasheet(115/160 Pages) AMCC

115 / 160 page

S5920 – PCI Product

Revision 1.01 – November 28, 2005

AMCC Confidential and Proprietary

DS1596

115

Data Book

Figure 61. 16 Bit Mode Operation Register DWORD Write/Read

Figure 3. 16 Bit Mode Operation Register DWORD

Write/Read Figure 3 shows an example of a DWORD

write of 12345678h using a 16 bit-mode write transfer,

and is described as follows:

Clock 1: ADR[6:2], BE[3:0], SELECT# and WR# are

driven, DQ[15:0] is driven with the data to be written.

BE3# is low indicating that the DQ bus data is to be

written to the lower WORD of the register. BE[2:0]# is

00h, indicating that both bytes on the DQ[15:0] bus are

valid and should be written to the register indicated by

ADR[6:2].

Clock 2: The rising edge of clock 2 writes 5678h into

the lower WORD of the register. 1234h is driven onto

the DQ[15:0] bus. BE3# is driven high, indicating the

DQ bus data is to be written to the upper WORD of the

of the WORD on DQ[15:0] bus is valid. This example

shows how the BEs function.

Clock 3: The rising edge of clock 3 writes 34h into the

lower byte of the upper WORD of the register.

BE[2:0]# is “01” indicating the upper byte on DQ[15:0]

is valid.

Clock 4: The rising edge of clock 4 writes 12h into the

upper byte of the upper WORD of the register.

12345678h is in the register selected by ADR[6:2].

SELECT#, ADR[6:2], WR#, BE[3:0]# and DQ are

deasserted. No read or write occurs on the rising edge

of clocks 5 and 6.

Figure 3 also shows a DWORD read of 12345678h

from the same register, using a 16-bit mode read

transfer, and is described as follows:

Clock 6: ADR[6:2], SELECT# and RD# are asserted.

BE3# is high, indicating the upper WORD of the regis-

ter is to be driven onto DQ[15:0] and BE[1:0]# is 00h

indicating both bytes of the WORD are to be driven.

Clock 7: The S5920 drives 1234h onto DQ[15:0] as a

result of the read issued during the previous cycle.

BE3# is next driven low to indicate the lower WORD of

the register is to be driven onto DQ[15:0]. BE[1:0]# is

00h indicating both bytes of the WORD should be

driven onto DQ[15:0]. Note: in the event that BE[0]#

was 1b, DQ[7:0] would NOT be driven during Clock 8,

it would remain tri-state. The only exception to this is if

ADR[6:2] indicated the Pass-Thru Data Register,

where all of DQ[15:0] would be driven, regardless of

the state of BE[1:0]#.

Clock 8: On the rising-edge, Add-On logic latches data

1234h. The S5920 drives 5678h onto DQ[15:0] as a

result of the read issued during the previous cycle.

ADR[6:2], SELECT#, RD# and BE[3:0]# are deas-

serted, completing the transfer.

Clock 9: On the rising-edge, Add-On logic latches data

5678h. DQ[15:0] returns to tri-state as RD# was sam-

pled deasserted.

ADCLK

WR#

SELECT#

1234

ADR[6:2]

BE3#

RD#

DQ[15:0]

5678h

56789

BE[1:0]#

DQMODE

1234h

1234

5678h

00b

60h

10b

01b

00b

60h

CS5920 Datasheet(PDF) 115 Page - Applied Micro Circuits Corporation

CS5920 Datasheet(HTML) 115 Page - Applied Micro Circuits Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL