Electronic Components Datasheet Search
  English  ▼

X  

SC908 Datasheet(PDF) 18 Page - Semtech Corporation

Part # SC908
Description  Power Management IC for Single-Cell Li-Ion Devices
PDF  30 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  SEMTECH [Semtech Corporation]
Direct Link  http://www.semtech.com
Logo SEMTECH - Semtech Corporation

SC908 Datasheet(HTML) 18 Page - Semtech Corporation

Back Button SC908 Datasheet HTML 14Page - Semtech Corporation SC908 Datasheet HTML 15Page - Semtech Corporation SC908 Datasheet HTML 16Page - Semtech Corporation SC908 Datasheet HTML 17Page - Semtech Corporation SC908 Datasheet HTML 18Page - Semtech Corporation SC908 Datasheet HTML 19Page - Semtech Corporation SC908 Datasheet HTML 20Page - Semtech Corporation SC908 Datasheet HTML 21Page - Semtech Corporation SC908 Datasheet HTML 22Page - Semtech Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 18 / 30 page
background image
SC908
18
Applications Information (continued)
NTC thresholds to avoid chatter at the NTC fault thresh-
olds. When V
EN_NTC
returns to the valid range, the charge
timer resumes and the charge cycle continues. The charge
timer will expire when the output on-time exceeds the
timer setting, regardless of how long it has been disabled
due to an NTC fault.
Using the recommended NTC external network, the
EN_NTC pin voltage and the internal hot and cold NTC
thresholds are all ratios of V
VSYS
, rather than absolute volt-
ages. This ensures that the hot and cold OK-to-charge
thresholds are insensitive to the VSYS pin output voltage.
The ratiometric thresholds are given by the parameters
RT
NTCH
and RT
NTCC
. EN_NTC pin voltage V
EN_NTC
between
RT
NTCH×V
VSYS
and RT
NTCC×V
VSYS
enables charging. When V
EN_NTC
is outside this range, charging is suspended and the FLTB
output is asserted (pulled low).
When V
EN_NTC
< VT
NTCDIS (nominally 0.6V), the SC908 charger
is disabled. The EN_NTC pin can be pulled to ground by
an external n-channel FET or microprocessor GPIO to
asnychronously disable or reset the device. When V
EN_NTC
<
VT
NTC_DIS
, the charger is turned off, the charge timer is reset,
and the CHRGB status output is turned off. While disabled,
the VAD input UVLO and OVP threshold detectors remain
active, and the CPB pin continues to indicate whether the
VAD input voltage is valid for charging.
The response of the SC908 to an EN_NTC pin voltage
above the high threshold or below the low threshold (but
above VT
NTCDIS) is the same. Therefore the EN_NTC network
can be configured with the battery pack thermistor
between EN_NTC and VSYS, and a fixed resistor between
EN_NTC and ground. This configuration may be used to
reset the charge timer (and the CHRGB output) when the
battery pack is removed; the fixed resistor pulls the NTC
pin to ground to disable the charger without indicating a
fault.
NTC Design Example
This example uses the conventional NTC network configu-
ration shown in the block diagram. A fixed resistor (R
NPU
)
is connected between EN_NTC and VSYS, and a battery
NTC thermistor (R
NTC
) is connected between the EN_NTC
pin and ground. The battery temperature range over
which charging is permitted is from 0°C to 40°C. The data-
sheet for the proposed NTC thermistor, the Mitsubishi
TH11-3T223F, indicates that R
NTC
= 11.93kΩ at 40°C, and
R
NTC
= 69.41kΩ at 0°C, with a dissipation constant
DC = 3.0mW/°C. So R
HOT
= 11.93kΩ and R
COLD
= 69.41kΩ.
Step 1
Select R
NPU
to obtain one of the desired temperature
thresholds. This example will solve for the hot threshold
for the normal (NTC thermistor to ground) configuration,
then evaluate the cold threshold. Solve the NTC network
voltage divider for R
NPU
to place the NTC voltage at
RT
NTC_HF
× V
VSYS
when R
NTC
= R
HOT
.
HOT
NPU
HOT
VSYS
VSYS
HF
_
NTC
R
R
R
V
V
RT
or, solving for R
NPU
,
HOT
HF
_
NTC
HF
_
NTC
NPU
R
RT
RT
R
1
Using RT
NTC_HF
= 0.3, we obtain R
NPU
= 27.837kΩ exactly.
The closest 1% standard nominal value is R
NPU
= 28.0kΩ.
Step 2
Evaluate the NTC network at the cold threshold. Compute
the NTC network resistor divider voltage as a function of
V
VSYS
at the desired cold threshold.
VSYS
COLD
NPU
COLD
VSYS
COLD
V
7126
.
0
R
R
R
V
NTC
The value 0.7126 should be close to the nominal value of
RT
NTC_CR
= 0.75. To evaluate the significance of the discrep-
ancy, an estimate of the actual cold threshold is obtained
by evaluating the value of R
NTC_Cold_Actual
that produces
the nominal value of RT
NTC_CR
= 0.75.
NPU
Actual
_
Cold
_
NTC
Actual
_
Cold
_
NTC
CR
_
NTC
R
R
R
RT
The solution shows R
NTC_Cold_Actual
= 84.0kΩ. Examination of
the thermistor specification resistance versus temperature
data indicates that the resulting actual cold threshold is
approximately -4°C, compared to the target of 0°C.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com