LTC2216 datasheet(18/36 Pages) LINER

18 / 36 page

LTC2216/LTC2215

22165f

For CMOS Mode. Full Rate or Demultiplexed

SENSE (Pin 1): Reference Mode Select and External Refer-

ence Input. Tie SENSE to VDD to select the internal 2.5V

bandgap reference. An external reference of 2.5V or 1.25V

may be used; both reference values will set a full-scale

ADC range of 2.75V.

GND (Pins 2, 4, 7, 10, 11, 14, 18): ADC Power Ground.

VCM(Pin3):1.575VOutput.Optimumvoltageforinputcom-

mon mode. Must be bypassed to ground with a minimum

of 2.2μF. Ceramic chip capacitors are recommended.

VDD (Pins 5, 6, 15, 16, 17): 3.3V Analog Supply Pin.

Bypass to GND with 1μF ceramic chip capacitors.

AIN+ (Pin 8): Positive Differential Analog Input.

AIN– (Pin 9): Negative Differential Analog Input.

ENC+ (Pin 12): Positive Differential Encode Input. The

sampled analog input is held on the rising edge of ENC+.

Internally biased to 1.6V through a 6.2k

Ω resistor. Output

data can be latched on the rising edge of ENC+.

ENC– (Pin 13): Negative Differential Encode Input. The

sampled analog input is held on the falling edge of ENC–.

Internally biased to 1.6V through a 6.2k

Ω resistor. By-

pass to ground with a 0.1μF capacitor for a single-ended

Encode signal.

SHDN (Pin 19): Power Shutdown Pin. SHDN = low results

in normal operation. SHDN = high results in powered

down analog circuitry and the digital outputs are placed

in a high impedance state.

DITH (Pin 20): Internal Dither Enable Pin. DITH = low

disables internal dither. DITH = high enables internal dither.

Refer to Internal Dither section of this data sheet for details

on dither operation.

DB0-DB15 (Pins 21-30 and 33-38): Digital Outputs, B Bus.

DB15 is the MSB. Active in demultiplexed mode. The B bus

is in high impedance state in full rate CMOS mode.

OGND (Pins 31 and 50): Output Driver Ground.

OVDD (Pins 32 and 49): Positive Supply for the Output

Drivers. Bypass to ground with 1μF capacitor.

OFB (Pin 39): Over/Under Flow Digital Output for the B Bus.

OFB is high when an over or under ﬂow has occurred on the

B bus. At high impedance state in full rate CMOS mode.

CLKOUTB (Pin 40): Data Valid Output. CLKOUTB will toggle

at the sample rate in full rate CMOS mode or at 1/2 the

sample rate in demultiplexed mode. Latch the data on the

falling edge of CLKOUTB.

CLKOUTA (Pin 41): Inverted Data Valid Output. CLKOUTA

will toggle at the sample rate in full rate CMOS mode or

at 1/2 the sample rate in demultiplexed mode. Latch the

data on the rising edge of CLKOUTA.

DA0-DA15 (Pins 42-48 and 51-59): Digital Outputs, A Bus.

DA15 is the MSB. Output bus for full rate CMOS mode

and demultiplexed mode.

OFA (Pin 60): Over/Under Flow Digital Output for the A

Bus. OFA is high when an over or under ﬂow has occurred

on the A bus.

LVDS (Pin 61): Data Output Mode Select Pin. Connecting

LVDS to 0V selects full rate CMOS mode. Connecting LVDS

to 1/3VDD selects demultiplexed CMOS mode. Connecting

LVDS to 2/3VDD selects Low Power LVDS mode. Connect-

ing LVDS to VDD selects Standard LVDS mode.

MODE (Pin 62): Output Format and Clock Duty Cycle

Stabilizer Selection Pin. Connecting MODE to 0V selects

offset binary output format and disables the clock duty

cycle stabilizer. Connecting MODE to 1/3VDD selects offset

binary output format and enables the clock duty cycle sta-

bilizer. Connecting MODE to 2/3VDDselects2’scomplement

output format and enables the clock duty cycle stabilizer.

Connecting MODE to VDD selects 2’s complement output

format and disables the clock duty cycle stabilizer.

RAND (Pin 63): Digital Output Randomization Selection

Pin. RAND low results in normal operation. RAND high

selects D1-D15 to be EXCLUSIVE-ORed with D0 (the

LSB). The output can be decoded by again applying an

XOR operation between the LSB and all other bits. This

mode of operation reduces the effects of digital output

interference.

NC (Pin 64): Not Connected Internally. For pin compatibility

with the LTC2208 this pin should be connected to GND or

VDD as required. Otherwise no connection.

GND (Exposed Pad): ADC Power Ground. The exposed

pad on the bottom of the package must be soldered to

ground.

PIN FUNCTIONS

LTC2216 Datasheet(PDF) 18 Page - Linear Technology

LTC2216 Datasheet(HTML) 18 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

Datasheet Download

Link URL