TMS320VC5421 datasheet(28/88 Pages) TI

28 / 88 page

TMS320VC5421

DIGITAL SIGNAL PROCESSOR

SPRS098 – DECEMBER 1999

POST OFFICE BOX 1443

• HOUSTON, TEXAS 77251–1443

multichannel buffered serial port (McBSP) (continued)

The selection of the sample rate generator (SRG) clock input source is made by the combination of the CLKSM

and SCLKME bit values as shown in Table 7.

Table 7. Sample Rate Generator Clock Source Selection

SCLKME

CLKSM

SRG Clock Source

CLKS (not available as a pin on ’5421)

CPU clock

BCLKR pin

BCLKX pin

When either of the bidirectional pins, BCLKR or BCLKX, is configured as the clock input, its output buffer is

automatically disabled. For example, with SCLKME = 1 and CLKSM = 0, the BCLKR pin is configured as the

SRG input. In this case, both the transmitter and receiver circuits can be synchronized to the SRG output by

setting the PCR bits (9:8) for CLKXM = 1 and CLKRM = 1. However, the SRG output is only driven onto the

BCLKX pin because the BCLKR output is automatically disabled.

The McBSP supports independent selection of multiple channels for the transmitter and receiver. When multiple

channels are selected, each frame represents a time-division multiplexed (TDM) data stream. In using

time-division multiplexed data streams, the CPU may only need to process a few of them. Thus, to save memory

and bus bandwidth, multichannel selection allows independent enabling of particular channels for transmission

and reception. Up to a maximum of 128 channels in a bit stream can be enabled or disabled.

The ’5421 McBSPs have two working modes that are selected by setting the RMCME and XMCME bits in the

multichannel control registers (MCR1x and MCR2x, respectively). See Figure 9 and Figure 10. For a

description of the remaining bits, see

TMS320C54x DSP Reference Set, Volume 5: Enhanced Peripherals

(literature number SPRU302).

D In the first mode, when RMCME = 0 and XMCME = 0, there are two partitions (A and B), with each containing

16 channels as shown in Figure 9 and Figure 10. This is compatible with the McBSPs used in the ’5420,

where only 32-channel selection is enabled (default).

Reserved

XMC

XPBBLK

XPABLK

XCBLK

XMCM

R,+0

RW,+0

R,+0

RW,+0

Note:

R = Read, W = Write, +0 = Value at reset; x = McBSP 0,1, or 2

Figure 9. Multichannel Control Register 2x (MCR2x)

Reserved

RMC

RPBBLK

RPABLK

RCBLK

RMCM

R,+0

RW,+0

R,+0

RW,+0

Note:

R = Read, W = Write, +0 = Value at reset; x = McBSP 0,1, or 2

Figure 10. Multichannel Control Register 1x (MCR1x)

TMS320VC5421 Datasheet(PDF) 28 Page - Texas Instruments

TMS320VC5421 Datasheet(HTML) 28 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

Datasheet Download

Link URL