ATmega324P datasheet(216/377 Pages) ATMEL

216 / 377 page

216

7674F–AVR–09/09

ATmega164P/324P/644P

19.5.1

SCL and SDA Pins

These pins interface the AVR TWI with the rest of the MCU system. The output drivers contain a

slew-rate limiter in order to conform to the TWI specification. The input stages contain a spike

suppression unit removing spikes shorter than 50 ns. Note that the internal pull-ups in the AVR

pads can be enabled by setting the PORT bits corresponding to the SCL and SDA pins, as

explained in the I/O Port section. The internal pull-ups can in some systems eliminate the need

for external ones.

19.5.2

Bit Rate Generator Unit

This unit controls the period of SCL when operating in a Master mode. The SCL period is con-

trolled by settings in the TWI Bit Rate Register (TWBR) and the Prescaler bits in the TWI Status

CPU clock frequency in the Slave must be at least 16 times higher than the SCL frequency. Note

that slaves may prolong the SCL low period, thereby reducing the average TWI bus clock

period. The SCL frequency is generated according to the following equation:

• TWBR = Value of the TWI Bit Rate Register.

• TWPS = Value of the prescaler bits in the TWI Status Register.

Note:

Pull-up resistor values should be selected according to the SCL frequency and the capacitive bus

line load. See 2-wire Serial Bus Requirements in Table 26-7 on page 334 for value of pull-up

resistor.

19.5.3

Bus Interface Unit

This unit contains the Data and Address Shift Register (TWDR), a START/STOP Controller and

Arbitration detection hardware. The TWDR contains the address or data bytes to be transmitted,

or the address or data bytes received. In addition to the 8-bit TWDR, the Bus Interface Unit also

contains a register containing the (N)ACK bit to be transmitted or received. This (N)ACK Regis-

ter is not directly accessible by the application software. However, when receiving, it can be set

or cleared by manipulating the TWI Control Register (TWCR). When in Transmitter mode, the

value of the received (N)ACK bit can be determined by the value in the TWSR.

The START/STOP Controller is responsible for generation and detection of START, REPEATED

START, and STOP conditions. The START/STOP controller is able to detect START and STOP

conditions even when the AVR MCU is in one of the sleep modes, enabling the MCU to wake up

if addressed by a Master.

If the TWI has initiated a transmission as Master, the Arbitration Detection hardware continu-

ously monitors the transmission trying to determine if arbitration is in process. If the TWI has lost

an arbitration, the Control Unit is informed. Correct action can then be taken and appropriate

status codes generated.

SCL frequency

CPU Clock frequency

2(TWBR)

TWPS

⋅

--------------------------------------------------------------

ATmega324P Datasheet(PDF) 216 Page - ATMEL Corporation

ATmega324P Datasheet(HTML) 216 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL