ATmega324P datasheet(217/377 Pages) ATMEL

217 / 377 page

217

7674F–AVR–09/09

ATmega164P/324P/644P

19.5.4

Address Match Unit

The Address Match unit checks if received address bytes match the seven-bit address in the

TWI Address Register (TWAR). If the TWI General Call Recognition Enable (TWGCE) bit in the

TWAR is written to one, all incoming address bits will also be compared against the General Call

address. Upon an address match, the Control Unit is informed, allowing correct action to be

taken. The TWI may or may not acknowledge its address, depending on settings in the TWCR.

The Address Match unit is able to compare addresses even when the AVR MCU is in sleep

mode, enabling the MCU to wake up if addressed by a Master. If another interrupt (e.g., INT0)

occurs during TWI Power-down address match and wakes up the CPU, the TWI aborts opera-

tion and return to it’s idle state. If this cause any problems, ensure that TWI Address Match is the

only enabled interrupt when entering Power-down.

19.5.5

Control Unit

The Control unit monitors the TWI bus and generates responses corresponding to settings in the

TWI Control Register (TWCR). When an event requiring the attention of the application occurs

on the TWI bus, the TWI Interrupt Flag (TWINT) is asserted. In the next clock cycle, the TWI Sta-

tus Register (TWSR) is updated with a status code identifying the event. The TWSR only

contains relevant status information when the TWI Interrupt Flag is asserted. At all other times,

the TWSR contains a special status code indicating that no relevant status information is avail-

able. As long as the TWINT Flag is set, the SCL line is held low. This allows the application

software to complete its tasks before allowing the TWI transmission to continue.

The TWINT Flag is set in the following situations:

• After the TWI has transmitted a START/REPEATED START condition.

• After the TWI has transmitted SLA+R/W.

• After the TWI has transmitted an address byte.

• After the TWI has lost arbitration.

• After the TWI has been addressed by own slave address or general call.

• After the TWI has received a data byte.

• After a STOP or REPEATED START has been received while still addressed as a Slave.

• When a bus error has occurred due to an illegal START or STOP condition.

19.6

Using the TWI

The AVR TWI is byte-oriented and interrupt based. Interrupts are issued after all bus events, like

reception of a byte or transmission of a START condition. Because the TWI is interrupt-based,

the application software is free to carry on other operations during a TWI byte transfer. Note that

the TWI Interrupt Enable (TWIE) bit in TWCR together with the Global Interrupt Enable bit in

SREG allow the application to decide whether or not assertion of the TWINT Flag should gener-

ate an interrupt request. If the TWIE bit is cleared, the application must poll the TWINT Flag in

order to detect actions on the TWI bus.

When the TWINT Flag is asserted, the TWI has finished an operation and awaits application

response. In this case, the TWI Status Register (TWSR) contains a value indicating the current

state of the TWI bus. The application software can then decide how the TWI should behave in

the next TWI bus cycle by manipulating the TWCR and TWDR Registers.

ATmega324P Datasheet(PDF) 217 Page - ATMEL Corporation

ATmega324P Datasheet(HTML) 217 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL