 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
TMS320DM365 Datasheet(PDF) 39 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
TMS320DM365 Datasheet(HTML) 39 Page - Texas Instruments |
|
|
39 / 211 page  TMS320DM365 www.ti.com SPRS457C – MARCH 2009 – REVISED APRIL 2010 Table 2-5. Pin Descriptions (continued) Name BGA Type Group Power IPU Reset Description(4) ID (1) Supply(2) IPD(3) State GIO5 / B4 I/O/Z GIO / VDDS33 IPD Input GIO: GIO[05] EMAC_RX_DV EMAC EMAC: Receive data valid input GIO4 / A4 I/O/Z GIO / VDDS33 IPD Input GIO: GIO[04] EMAC_RX_ER EMAC EMAC: Receive error input GIO3 / C5 I/O/Z GIO / VDDS33 IPD Input GIO: GIO[03] EMAC_CRS EMAC EMAC: Carrier sense input GIO2 / MDIO C4 I/O/Z GIO / VDDS33 IPD Input GIO: GIO[02] EMAC EMAC: Management Data I/O GIO1 / MDCLK D6 I/O/Z GIO / VDDS33 IPD Input GIO: GIO[01] EMAC EMAC: Management Data clock output GIO0 B5 I/O/Z GIO VDDS33 IPD Input GIO: GIO[00] USB_DP N1 A I/O USBPH VDDA33_USB USB D+ (differential signal pair) Y Note: If the USB peripheral is not used at all in the application, this pin should be connected to 3.3V . USB_DM P1 A I/O USBPH VDDA33_USB USB D- (differential signal pair) Y Note: If the USB peripheral is not used at all in the application, this pin should be connected to VSS. VDDA33_USB P4 PWR 3.3-V USB analog power supply Note: If the USB peripheral is not used at all in the application, this pin should be connected to 3.3V. VSSA33_USB P3 GND 3.3-V USB ground Note: If the USB peripheral is not used at all in the application, this pin should be connected to VSS. VDDA12LDO_USB M5 PWR Output For proper device operation, even if the USB peripheral is not used, a 0.22µF capacitor must be connected as close as possible to the package, and the capacitor mst be connected to VSSA. VDDA18_USB N5 PWR 1.8-V USB analog power supply Note: If the USB peripheral is not used at all in the application, this pin should be connected to 1.8V. VSSA18_USB P2 GND 1.8-V USB ground Note: If the USB peripheral is not used at all in the application, this pin should be connected to VSS. USB_ID M1 A I USBPH VDDA33_USB USB operating mode identification pin. Y For device mode operation only, pull up this pin to VDD with a 1.5K ohm resistor. For host mode operation only, pull down this pin to ground (VSS) with a 1.5K ohm resistor. If using an OTG or mini-USB connector, this pin will be set properly via the cable/connector configuration. Note: If the USB peripheral is not used at all in the application, this pin should be connected to 3.3V. Copyright © 2009–2010, Texas Instruments Incorporated Device Overview 39 Submit Documentation Feedback Product Folder Link(s): TMS320DM365 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
