AD7710 datasheet(6/28 Pages) AD

6 / 28 page

REV. F

–6–

AD7710

Limit at TMIN, TMAX

Parameter

(A, S Versions)

Units

Conditions/Comments

External Clocking Mode

fSCLK

fCLK IN/5

MHz max

Serial Clock Input Frequency

t20

ns min

DRDY to RFS Setup Time

t21

ns min

DRDY to RFS Hold Time

t22

× t

CLK IN

ns min

A0 to

RFS Setup Time

t23

ns min

A0 to

RFS Hold Time

t24

× t

CLK IN

ns max

Data Access Time (

RFS Low to Data Valid)

t25

ns min

SCLK Falling Edge to Data Valid Delay

× t

CLK IN + 20

ns max

t26

× t

CLK IN

ns min

SCLK High Pulsewidth

t27

× t

CLK IN

ns min

SCLK Low Pulsewidth

t28

tCLK IN + 10

ns max

SCLK Falling Edge to

DRDY High

t29

ns min

SCLK to Data Valid Hold Time

tCLK IN + 10

ns max

t30

ns min

RFS/TFS to SCLK Falling Edge Hold Time

t31

× t

CLK IN/2 + 50

ns max

RFS to Data Valid Hold Time

t32

ns min

A0 to

TFS Setup Time

t33

ns min

A0 to

TFS Hold Time

t34

× t

CLK IN

ns min

SCLK Falling Edge to

TFS Hold Time

t35

× t

CLK IN – SCLK High

ns min

Data Valid to SCLK Setup Time

t36

ns min

Data Valid to SCLK Hold Time

NOTES

1Guaranteed by design, not production tested. All input signals are specified with tr = tf = 5 ns (10% to 90% of 5 V) and timed from a voltage level of 1.6 V.

2See Figures 10 to 13.

3The AD7710 is specified with a 10 MHz clock for AV

DD voltages of +5 V

± 5%. It is specified with an 8 MHz clock for AV

DD voltages greater than 5.25 V and less

than 10.5 V.

4CLK IN duty cycle range is 45% to 55%. CLK IN must be supplied whenever the AD7710 is not in STANDBY mode. If no clock is present in this case, the device

can draw higher current than specified and possibly become uncalibrated.

5The AD7710 is production tested with f

CLK IN at 10 MHz (8 MHz for AVDD > +5.25 V). It is guaranteed by characterization to operate at 400 kHz.

6Specified using 10% and 90% points on waveform of interest.

7These numbers are measured with the load circuit of Figure 1 and defined as the time required for the output to cross 0.8 V or 2.4 V.

8These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then

extrapolated back to remove effects of charging or discharging the 100 pF capacitor. This means that the times quoted in the timing characteristics are the true bus

relinquish times of the part and, as such, are independent of external bus loading capacitances.

Specifications subject to change without notice.

PIN CONFIGURATION

DIP AND SOIC

SCLK

MCLK IN

DGND

DVDD

MODE

AIN1(+)

AGND

MCLK OUT

SDATA

AIN1(–)

IOUT

REF OUT

REF IN(+)

REF IN(–)

AVDD

VBIAS

817

916

TOP VIEW

(Not to Scale)

AD7710

SYNC

VSS

DRDY

RFS

TFS

AIN2(+)

AIN2(–)

TO OUTPUT

+2.1V

1.6mA

200 A

100pF

Figure 1. Load Circuit for Access Time and Bus Relinquish

Time

AD7710 Datasheet(PDF) 6 Page - Analog Devices

AD7710 Datasheet(HTML) 6 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Datasheet Download

Link URL