DOC7707 datasheet(232/307 Pages) ETC1

232 / 307 page

232

7707F–AVR–11/10

AT90USB82/162

after SIGRD and SPMEN are set will have no effect. This operation is reserved for future use

and should not be used.

• Bit 4 – RWWSRE: Read-While-Write Section Read Enable

When programming (Page Erase or Page Write) to the RWW section, the RWW section is

blocked for reading (the RWWSB will be set by hardware). To re-enable the RWW section, the

user software must wait until the programming is completed (SPMEN will be cleared). Then, if

the RWWSRE bit is written to one at the same time as SPMEN, the next SPM instruction within

four clock cycles re-enables the RWW section. The RWW section cannot be re-enabled while

the Flash is busy with a Page Erase or a Page Write (SPMEN is set). If the RWWSRE bit is writ-

ten while the Flash is being loaded, the Flash load operation will abort and the data loaded will

be lost.

• Bit 3 – BLBSET: Boot Lock Bit Set

If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock

cycles sets Boot Lock bits, according to the data in R0. The data in R1 and the address in the Z-

pointer are ignored. The BLBSET bit will automatically be cleared upon completion of the Lock

bit set, or if no SPM instruction is executed within four clock cycles.

An (E)LPM instruction within three cycles after BLBSET and SPMEN are set in the SPMCSR

destination register. See “Reading the Fuse and Lock Bits from Software” on page 235 for

details.

• Bit 2 – PGWRT: Page Write

If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock

cycles executes Page Write, with the data stored in the temporary buffer. The page address is

taken from the high part of the Z-pointer. The data in R1 and R0 are ignored. The PGWRT bit

will auto-clear upon completion of a Page Write, or if no SPM instruction is executed within four

clock cycles. The CPU is halted during the entire Page Write operation if the NRWW section is

addressed.

• Bit 1 – PGERS: Page Erase

If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock

cycles executes Page Erase. The page address is taken from the high part of the Z-pointer. The

data in R1 and R0 are ignored. The PGERS bit will auto-clear upon completion of a Page Erase,

or if no SPM instruction is executed within four clock cycles. The CPU is halted during the entire

Page Write operation if the NRWW section is addressed.

• Bit 0 – SPMEN: Store Program Memory Enable

This bit enables the SPM instruction for the next four clock cycles. If written to one together with

either RWWSRE, BLBSET, PGWRT’ or PGERS, the following SPM instruction will have a spe-

cial meaning, see description above. If only SPMEN is written, the following SPM instruction will

store the value in R1:R0 in the temporary page buffer addressed by the Z-pointer. The LSB of

the Z-pointer is ignored. The SPMEN bit will auto-clear upon completion of an SPM instruction,

or if no SPM instruction is executed within four clock cycles. During Page Erase and Page Write,

the SPMEN bit remains high until the operation is completed.

Writing any other combination than “10001”, “01001”, “00101”, “00011” or “00001” in the lower

five bits will have no effect.

DOC7707 Datasheet(PDF) 232 Page - List of Unclassifed Manufacturers

DOC7707 Datasheet(HTML) 232 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL