DOC7707 datasheet(235/307 Pages) ETC1

235 / 307 page

235

7707F–AVR–11/10

AT90USB82/162

be moved to the BLS section to avoid that an interrupt is accessing the RWW section when it is

blocked for reading. How to move the interrupts is described in “Interrupts” on page 63.

23.7.5

Consideration While Updating BLS

Special care must be taken if the user allows the Boot Loader section to be updated by leaving

Boot Lock bit11 unprogrammed. An accidental write to the Boot Loader itself can corrupt the

entire Boot Loader, and further software updates might be impossible. If it is not necessary to

change the Boot Loader software itself, it is recommended to program the Boot Lock bit11 to

protect the Boot Loader software from any internal software changes.

23.7.6

Prevent Reading the RWW Section During Self-Programming

During Self-Programming (either Page Erase or Page Write), the RWW section is always

blocked for reading. The user software itself must prevent that this section is addressed during

the self programming operation. The RWWSB in the SPMCSR will be set as long as the RWW

section is busy. During Self-Programming the Interrupt Vector table should be moved to the BLS

as described in “Interrupts” on page 63, or the interrupts must be disabled. Before addressing

the RWW section after the programming is completed, the user software must clear the

RWWSB by writing the RWWSRE. See “Simple Assembly Code Example for a Boot Loader” on

page 237 for an example.

23.7.7

Setting the Boot Loader Lock Bits by SPM

To set the Boot Loader Lock bits, write the desired data to R0, write “X0001001” to SPMCSR

and execute SPM within four clock cycles after writing SPMCSR. The only accessible Lock bits

are the Boot Lock bits that may prevent the Application and Boot Loader section from any soft-

ware update by the MCU.

See Table 23-2 and Table 23-3 for how the different settings of the Boot Loader bits affect the

Flash access.

If bits 5..2 in R0 are cleared (zero), the corresponding Boot Lock bit will be programmed if an

SPM instruction is executed within four cycles after BLBSET and SPMEN are set in SPMCSR.

The Z-pointer is don’t care during this operation, but for future compatibility it is recommended to

load the Z-pointer with 0x0001 (same as used for reading the lO

ck bits). For future compatibility it

is also recommended to set bits 7, 6, 1, and 0 in R0 to “1” when writing the Lock bits. When pro-

gramming the Lock bits the entire Flash can be read during the operation.

23.7.8

EEPROM Write Prevents Writing to SPMCSR

Note that an EEPROM write operation will block all software programming to Flash. Reading the

Fuses and Lock bits from software will also be prevented during the EEPROM write operation. It

is recommended that the user checks the status bit (EEPE) in the EECR Register and verifies

that the bit is cleared before writing to the SPMCSR Register.

23.7.9

Reading the Fuse and Lock Bits from Software

It is possible to read both the Fuse and Lock bits from software. To read the Lock bits, load the

Z-pointer with 0x0001 and set the BLBSET and SPMEN bits in SPMCSR. When an (E)LPM

instruction is executed within three CPU cycles after the BLBSET and SPMEN bits are set in

SPMCSR, the value of the Lock bits will be loaded in the destination register. The BLBSET and

SPMEN bits will auto-clear upon completion of reading the Lock bits or if no (E)LPM instruction

Bit

BLB12

BLB11

BLB02

BLB01

DOC7707 Datasheet(PDF) 235 Page - List of Unclassifed Manufacturers

DOC7707 Datasheet(HTML) 235 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL