DOC7707 datasheet(97/307 Pages) ETC1

97 / 307 page

7707F–AVR–11/10

AT90USB82/162

PWM mode is shown in Figure 14-6. The TCNT0 value is in the timing diagram shown as a his-

togram for illustrating the single-slope operation. The diagram includes non-inverted and

inverted PWM outputs. The small horizontal line marks on the TCNT0 slopes represent Com-

pare Matches between OCR0x and TCNT0.

Figure 14-6. Fast PWM Mode, Timing Diagram

The Timer/Counter Overflow Flag (TOV0) is set each time the counter reaches TOP. If the inter-

rupt is enabled, the interrupt handler routine can be used for updating the compare value.

In fast PWM mode, the compare unit allows generation of PWM waveforms on the OC0x pins.

Setting the COM0x1:0 bits to two will produce a non-inverted PWM and an inverted PWM output

can be generated by setting the COM0x1:0 to three: Setting the COM0A1:0 bits to one allows

the OC0A pin to toggle on Compare Matches if the WGM02 bit is set. This option is not available

for the OC0B pin (See Table 14-3 on page 101). The actual OC0x value will only be visible on

the port pin if the data direction for the port pin is set as output. The PWM waveform is gener-

ated by setting (or clearing) the OC0x Register at the Compare Match between OCR0x and

TCNT0, and clearing (or setting) the OC0x Register at the timer clock cycle the counter is

cleared (changes from TOP to BOTTOM).

The PWM frequency for the output can be calculated by the following equation:

The N variable represents the prescale factor (1, 8, 64, 256, or 1024).

The extreme values for the OCR0A Register represents special cases when generating a PWM

waveform output in the fast PWM mode. If the OCR0A is set equal to BOTTOM, the output will

be a narrow spike for each MAX+1 timer clock cycle. Setting the OCR0A equal to MAX will result

in a constantly high or low output (depending on the polarity of the output set by the COM0A1:0

bits.)

A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by set-

ting OC0x to toggle its logical level on each Compare Match (COM0x1:0 = 1). The waveform

generated will have a maximum frequency of f

OC0 = fclk_I/O/2 when OCR0A is set to zero. This

TCNTn

OCRnx Update and

TOVn Interrupt Flag Set

Period

OCnx

(COMnx1:0 = 2)

(COMnx1:0 = 3)

OCRnx Interrupt Flag Set

OCnxPWM

fclk_I/O

N 256

⋅

------------------

DOC7707 Datasheet(PDF) 97 Page - List of Unclassifed Manufacturers

DOC7707 Datasheet(HTML) 97 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL