DOC7707 datasheet(258/307 Pages) ETC1

258 / 307 page

258

7707F–AVR–11/10

AT90USB82/162

Notes:

1. If the device is clocked by the internal Oscillator, it is no need to connect a clock source to the

XTAL1 pin.

2. VCC - 0.3V < AVCC < VCC + 0.3V, however, AVCC should always be within 1.8 - 5.5V

When programming the EEPROM, an auto-erase cycle is built into the self-timed programming

operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase

instruction. The Chip Erase operation turns the content of every memory location in both the

Program and EEPROM arrays into 0xFF.

Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods

for the serial clock (SCK) input are defined as follows:

Low: > 2 CPU clock cycles for f

ck < 12 MHz, 3 CPU clock cycles for fck >= 12 MHz

High: > 2 CPU clock cycles for f

ck < 12 MHz, 3 CPU clock cycles for fck >= 12 MHz

25.8.1

Serial Programming Algorithm

When writing serial data to the AT90USB82/162, data is clocked on the rising edge of SCK.

When reading data from the AT90USB82/162, data is clocked on the falling edge of SCK. See

Figure 25-11 for timing details.

To program and verify the AT90USB82/162 in the serial programming mode, the following

sequence is recommended (See four byte instruction formats in Table 25-16):

Power-up sequence:

Apply power between V

CC and GND while RESET and SCK are set to “0”. In some sys-

tems, the programmer can not guarantee that SCK is held low during power-up. In this

case, RESET must be given a positive pulse of at least two CPU clock cycles duration

after SCK has been set to “0”.

Wait for at least 20 ms and enable serial programming by sending the Programming

Enable serial instruction to pin PDI.

The serial programming instructions will not work if the communication is out of syn-

chronization. When in sync. the second byte (0x53), will echo back when issuing the

third byte of the Programming Enable instruction. Whether the echo is correct or not, all

four bytes of the instruction must be transmitted. If the 0x53 did not echo back, give

RESET a positive pulse and issue a new Programming Enable command.

The Flash is programmed one page at a time. The memory page is loaded one byte at

a time by supplying the 7 LSB of the address and data together with the Load Program

VCC

GND

XTAL1

SCK

PDO

PDI

RESET

+1.8 - 5.5V

AVCC

+1.8 - 5.5V

(2)

DOC7707 Datasheet(PDF) 258 Page - List of Unclassifed Manufacturers

DOC7707 Datasheet(HTML) 258 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL