| Electronic Components Datasheet Search |
|
LTC1562 Datasheet(PDF) 5 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC1562 Datasheet(HTML) 5 Page - Linear Technology |
|
5 / 28 page ![]() 5 LTC1562 PIN FUNCTIONS Shutdown (SHDN): When the SHDN input goes high or is open-circuited, the LTC1562 enters a “zero-power” shut- down state and only junction leakage currents flow. The AGND pin and the amplifier outputs (see Figure 3) assume a high impedance state and the amplifiers effectively disappear from the circuit. (If an input signal is applied to a complete filter circuit while the LTC1562 is in shutdown, some signal will normally flow to the output through passive components around the inactive op amps.) A small pull-up current source at the SHDN input defaults the LTC1562 to the shutdown state if the SHDN pin is left floating. Therefore, the user must connect the SHDN pin to a logic “low” (0V for ±5V supplies, V– for 5V total supply) for normal operation of the LTC1562. (This con- vention permits true “zero-power” shutdown since not even the driving logic must deliver current while the part is in shutdown.) With a single supply voltage, use V – for logic “low”— do not connect SHDN to the AGND pin. (Figure 1). For single supply operation, the AGND pin should be bypassed to the ground plane with at least a 0.1 µF capacitor (at least 1µF for best AC performance) (Figure 2). Figure 1. Dual Supply Ground Plane Connection (Including Substrate Pins 4, 7, 14, 17) 0.1 µF V– 1562 F01 DIGITAL GROUND PLANE (IF ANY) V+ LTC1562 0.1 µF ANALOG GROUND PLANE 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 SINGLE-POINT SYSTEM GROUND 1 µF 1562 F01 DIGITAL GROUND PLANE (IF ANY) V+ LTC1562 V+/2 REFERENCE 0.1 µF ANALOG GROUND PLANE 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 SINGLE-POINT SYSTEM GROUND Figure 2. Single Supply Ground Plane Connection (Including Substrate Pins 4, 7, 14, 17) + – R2 RQ VIN INV *R1 AND C ARE PRECISION INTERNAL COMPONENTS V2 V1 1/4 LTC1562 1562 F01 C 1 sR1C* ZIN ZIN TYPE R C RESPONSE AT V1 BANDPASS HIGHPASS RESPONSE AT V2 LOWPASS BANDPASS 10k Ω R2 IN EACH CASE, Q = fO = (100kHz) RQ R2 () 100kHz fO () Figure 3. Equivalent Circuit of a Single 2nd Order Section (Inside Dashed Line) Shown in Typical Connection. Form of ZIN Determines Response Types at the Two Outputs (See Table) |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |